吉林大学学报(工学版)

• • 上一篇    下一篇

集成化储能与姿态控制系统中飞轮高精度测速方法

刘治华12,贾宏光1,白越12,吴一辉1,詹迪铌3,杨作起12   

  1. 1.中国科学院 长春光学精密机械与物理研究所 应用光学国家重点实验室,长春 130033;2.中国科学院 研究生院,北京 100039;3.吉林大学 通信工程学院,长春 130022
  • 收稿日期:2005-09-10 修回日期:2005-12-04 出版日期:2006-03-24 发布日期:2006-03-24
  • 通讯作者: 吴一辉

High precision speed measurement method of flywheels in integrated energystorage and attitudecontrol system

Liu Zhihua1,2, Jia Hongguang1, Bai Yue1,2, Wu Yihui1, Zhan Dini3, Yang Zuoqi1,2   

  1. 1.State Key Lab of Applied Optics, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China; 2. Graduate School of Chinese Academy of Sciences, Beijing 100039, China; 3. College
  • Received:2005-09-10 Revised:2005-12-04 Online:2006-03-24 Published:2006-03-24
  • Contact: Wu Yihui

摘要: 针对集成化储能与姿态控制系统中飞轮速度测量要求范围宽、精度高的特点,从误差分析的角度提出了一种速度测量方法。该方法在低速阶段测量多个完整飞轮转速脉冲信号所用时间,跨越转速分界点进入高速阶段后,测量一定时间内飞轮转速脉冲信号个数。为了验证该测量方法的可行性,文中以Agilent公司生产的高精度信号发生器及信号计数器为基准对该系统进行了速度测量实验,并对实验结果进行了分析。结果表明,该系统具有测速精度高,测量范围宽的优点,完全能够满足集成化飞轮储能与姿态控制系统测速精度的要求。

关键词: 测速方法, 误差分析, 飞轮, 储能, 姿态控制

Abstract: To accomplish the wide range and high precision speed measurement in the attitude control and energy storage flywheel application, a new measurement method was put forward based on the analysis of the errors. In the low speed region, the time of several integrated flywheel speed pulse signal was measured. While the speed exceeds a certain threshold speed, the pulse number in a certain time was counted. For proving the feasibility of this method, the speed measurement experiment was done by using high precision arbitrary waveform generator and universal counter produced by Agilent Company, and the experiment results showed that the suggested speed measurement method can meet the demand of the integrated flywheel energy storage and attitude control system with the advantages of high precision and wide range.

Key words: speed measurement method, error analysis, flywheel, energy storage, attitude control

中图分类号: 

  • TH115
[1] 包广清, 毛振鹏. 基于超导储能系统的不对称电压跌落补偿方法[J]. 吉林大学学报(工学版), 2015, 45(4): 1234-1241.
[2] 朱晓林1, 2, 于鸣3, 高青1, 2, 王有镗1, 2. 地下换热管热变形引起的管-土间隙[J]. 吉林大学学报(工学版), 2014, 44(4): 998-1003.
[3] 赵静荣, 米阳, 张淑梅, 周劲. 人眼安全激光测距系统误差分析[J]. 吉林大学学报(工学版), 2012, 42(增刊1): 410-414.
[4] 刘敏时, 王晓曼, 景文博. 双波门自适应阈值法对光束质量M2因子 测量精度的影响[J]. , 2012, 42(04): 1066-1070.
[5] 李杨, 王永武, 张火成, 张娜, 邹玉峰. 磷酸铁锂动力电池动态SOC状态下的分选[J]. 吉林大学学报(工学版), 2011, 41(增刊2): 331-333.
[6] 安静1,2,武俊峰1,2,吴一辉1. 姿控飞轮电控系统电磁兼容设计[J]. 吉林大学学报(工学版), 2011, 41(4): 998-1003.
[7] 张刘,金光. 输入受限空间飞行器大角度机动控制器设计[J]. 吉林大学学报(工学版), 2010, 40(04): 1166-1170.
[8] 陈闽,张世杰,张迎春. 基于反作用飞轮和磁力矩器的小卫星姿态联合控制算法[J]. 吉林大学学报(工学版), 2010, 40(04): 1155-1160.
[9] 王宇航,姚郁,马克茂. 二阶扩张状态观测器的误差估计[J]. 吉林大学学报(工学版), 2010, 40(01): 143-0147.
[10] 郁发新,,孙琳琳 . 基于太阳矢量的皮卫星姿态角测量误差分析[J]. 吉林大学学报(工学版), 2008, 38(04): 976-980.
[11] 尹永鑫,杨明,王子才 . 复合控制拦截弹的神经网络姿态控制[J]. 吉林大学学报(工学版), 2008, 38(04): 981-985.
[12] 赵洪志;杨刚;孟庆海;王德全;张国民 . 转向球铰球面加工机床及误差分析[J]. 吉林大学学报(工学版), 2008, 38(03): 548-0551.
[13] 徐观,苏建,陈熔,张立斌,苏丽俐 . 汽车主销后倾测量模型误差分析及标定方法[J]. 吉林大学学报(工学版), 2008, 38(01): 17-020.
[14] 吴云华,曹喜滨,曾占魁,郑鹏飞 . 编队飞行卫星相对姿态变结构分布式协同控制[J]. 吉林大学学报(工学版), 2007, 37(06): 1465-1470.
[15] 郁发新,郑阳明,谢长雄,金佳军,金仲和 . 基于磁强计的皮卫星姿态角测量误差[J]. 吉林大学学报(工学版), 2007, 37(06): 1460-1464.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!