吉林大学学报(工学版) ›› 2011, Vol. 41 ›› Issue (增刊1): 127-133.

• 论文 • 上一篇    下一篇

产形线切齿法加工准双曲面齿轮的产形线建模及代用方法

李栎楠, 杨兆军, 王彦鹍, 张学成   

  1. 吉林大学机械科学与工程学院, 长春 130022
  • 收稿日期:2010-07-12 出版日期:2011-09-01 发布日期:2011-09-01
  • 通讯作者: 杨兆军(1956 ),男,教授.博士生导师.研究方向:复杂曲面成形理论与数控制造装备.数控装备可靠性理论与技术.E-mail:yzj@jlu.edu.cn. E-mail:yzj@jlu.edu.cn
  • 作者简介:李栋楠(1983 ),男,博士研究生.研究方向:复杂曲面成少任理沦与数控制造装备.E-mail:lilinan@foxmail.com.
  • 基金资助:

    高等学校博士学科点专项科研基金项目(20090061110023);吉林省科技发展计划重点项目(20080346);吉林大学研究生创新基金项目(20101019)

Modeling and substituting of generating lines of cutting hypoid gears by generating-line method

LI Li-nan, YANG Zhao-jun, WANG Yan-kun, ZHANG Xue-cheng   

  1. School of Mechanical Science and Engineering, Jilin University, Changchun 130022, China
  • Received:2010-07-12 Online:2011-09-01 Published:2011-09-01

PDF (PC)

886

摘要：

研究了准双曲面齿轮采用产形线切齿法加工时,小齿轮和大齿轮产形线的几何关系,建立产形线数学模型,提出以简单曲线代替复杂的理论产形线,从而简化机床运动的产形线代用方法。最后,以一对给定设计参数的准双曲面齿轮为例,在大轮产形线为直线的情况下,求解小轮左齿面和右齿面的理论产形线,并分别采用圆弧线和直线代用,分析代用误差对齿轮传动的影响及减小该影响的措施,表明采用代用产形线加工准双曲面齿轮的可行性。

关键词: 机械制造工艺与设备, 产形线切齿法, 产形线建模, 产形线代用

Abstract:

The geometrical relationship,which was used to manufacture hypoid gears by generating-line method,between two generating lines of pinion and gear was studied,and the mathematical model of generating lines was established.In order to simplify the movement of machine tool,the method of substituting simple curves for complex theoretical generating lines was proposed.Finally,taking a pair of hypoid gears,which the designing parameters were given and the gear generating line was straight,for example,the theoretical generating lines of left side and right side of pinion were solved and were substituted respectively by a circular arc and a straight line.The impact of substituting error on the gear drive and the measures of reducing this impact were analyzed,and it showed the feasibility of cutting hypoid gears by the substituted generating lines.

Key words: mechanical manufacturing technology and equipment, generating-line method, modeling of generating lines, substituting of generating lines

中图分类号: 

  • TH132.41


[1] Shih Yi-pei,Fong Zhang-hua,Grandle C Y.Mathematical model for a universal face hobbing hypoidgear generator
[J].Journal of Mechanical Design, 2007,129(1):38-47.

[2] Vimercati M.Mathematical model for tooth surfacesr epresentation of face-hobbed hypoid gears and itsa pplication to contact analysis and stress calculation
[J].Mechanism and Machine Theory,2007,42(6): 668-690.

[3] 王裕清,武良臣。弧齿锥齿轮接触区理论与切削过程仿真
[M].北京:煤炭工业出版社,2004:79-80.

[4] Wu Jun-long,Liu Chia-chang,Tsay Chung-biau,eta l.Mathematical model and surface deviation of helipoid gears cut by shaper cutters
[J].Journal of Mechanical Design,2003,125(2):351-355.

[5] 杨兆军,彭福华,张学成。球面渐开线齿形弧齿锥齿轮切齿法与机床
[P].中国:200810051354.3,2009-03-25.

[6] 彭福华。渐开线齿轮产形线切齿法
[M].长春:吉林 科学技术出版社,2008.

[7] 张学成,呼咏,杨兆军。基于齿面发生线的弧齿锥齿 轮切齿运动分析
[J].北京工业大学学报,2010,36 (11):1441-1446. Zhang Xue-cheng,Hu Yong,Yang Zhao-jun.Cuttingm ovement analysis of spiral bevel gear based on thet ooth generating line
[J].Journal of Beijing University of Technology,2010,36(11):1441-1446.

[8] Yang Zhao-jun,Li Li-nan,Wang Yan-kun,et al.Basic principle and mathematical model of cutting hypoid gears by generating line method
[J].Advanced Materials Research,2011,154-155:113-118.

[9] Yang Zhao-jun,Wang Yan-kun,Li Li-nan,et al.Mathematical model of spiral bevel gears manufactured by generating line method
[J].Advanced Materials Research,2011,154-155:103-108.

[10] Litvin F L.Gear Geometry and Applied Theory
[M].USA:Cambridge University Press,2004:78-152.

[11] 机械设计手册编委会。机械设计手册(单行本):齿轮 传动
[M].北京:机械工业出版社,2007.
[1] 寇淑清, 石舟. 裂解连杆接合面三维重构及其强度与刚度[J]. 吉林大学学报(工学版), 2018, 48(5): 1515-1523.
[2] 李俊烨, 胡敬磊, 杨兆军, 张心明, 周曾炜. 离散相磨粒粒径对磨粒流研抛共轨管质量的影响[J]. 吉林大学学报(工学版), 2018, 48(2): 492-499.
[3] 陈超, 赵升吨, 崔敏超, 韩晓兰, 范淑琴, 石田徹. AL5052铝合金板平压重塑形连接试验[J]. 吉林大学学报(工学版), 2017, 47(5): 1512-1518.
[4] 郎利辉, 阚鹏, 王耀, 孙志莹, 张泉达. 铝合金板材三向应力状态下的成形性能[J]. 吉林大学学报(工学版), 2017, 47(5): 1527-1533.
[5] 张鹏, 寇淑清, 赵勇, 林宝君. 装配式凸轮轴三点式轴向滚花过程[J]. 吉林大学学报(工学版), 2016, 46(6): 1953-1960.
[6] 王犇, 王晓力. 硅微球轴承关键工艺[J]. 吉林大学学报(工学版), 2016, 46(3): 824-830.
[7] 郭哲锋, 汤文成. 杯形件二次拉深的应力分析[J]. 吉林大学学报(工学版), 2016, 46(2): 494-499.
[8] 滕菲, 刘博, 张万喜, 高嵩. 柔性三维拉弯成形工艺稳健设计[J]. 吉林大学学报(工学版), 2015, 45(5): 1481-1487.
[9] 寇淑清, 张鹏, 韩广秘, 杨慎华. 装配式凸轮轴多道次扩径联接工艺[J]. 吉林大学学报(工学版), 2014, 44(2): 398-403.
[10] 寇淑清, 杨宏宇, 高岩, 杨慎华. 裂解连杆断裂结合面缺损面积定量描述与分析[J]. 吉林大学学报(工学版), 2013, 43(06): 1541-1545.
[11] 洪肇斌, 杨兆军, 张学成, 王佰超. 基于齿面发生线的弧齿锥齿轮铣削加工仿真分析[J]. 吉林大学学报(工学版), 2013, 43(02): 334-339.
[12] 宋占杰, 张美, 何改云, 刘佩佩. 基于质心Voronoi结构的自由曲面布点策略[J]. 吉林大学学报(工学版), 2013, 43(01): 34-38.
[13] 曲兴田, 王滨, 张雷, 邵奎伟, 张亮. 焊缝磨抛图像预处理技术[J]. , 2012, (06): 1421-1425.
[14] 李国发, 张栋林, 龚金龙, 王利斌. ZrO2陶瓷激光加热辅助切削加工技术[J]. , 2012, (06): 1409-1414.
[15] 张雷, 耿伟强, 鲍勇吉, 赵继. 用于羟基磷灰石冷喷涂的超声波送粉系统[J]. , 2012, (06): 1402-1408.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 《吉林大学学报(工学版)》编辑部
地址：长春市人民大街5988号　电话：+86-431-85095297　传真：+86-431-85094074　E-mail: xbgxb@jlu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发