J4

• 地球物理·勘查技术 • 上一篇    

节水型液动冲击器及风动钢球冲击器研究

卢春华1,鄢泰宁1,Н.Г.叶戈罗夫2,蒋国盛1,吴翔1   

  1. 1.中国地质大学 研究生院,武汉 430074;2.俄罗斯自然资源部 地质研究所,俄罗斯 图拉 300026
  • 收稿日期:2006-10-09 修回日期:1900-01-01 出版日期:2007-07-26 发布日期:2007-07-26
  • 通讯作者: 卢春华

Study on Water-Saving Hydro-Percussive Tools and Pneumatic Steel Ball Percussion Tools

LU Chun-hua1, YAN Tai-ning1, Н.Г. Egorov2, JIANG Guo-sheng1, WU Xiang1   

  1. 1.Graduate School, China University of Geosciences, Wuhan 430074,China;2.Russia Science Research Institute of Geology, Tula 300026, Russia
  • Received:2006-10-09 Revised:1900-01-01 Online:2007-07-26 Published:2007-07-26
  • Contact: LU Chun-hua

摘要: 中国许多地区严重缺水的现状及国家地质大调查战略的实施,使得如何快速、高效钻进干旱缺水地区大量遇到的软-中硬岩层成为当务之急。从分析干旱缺水地区节水型冲击器的设计思路出发,对两种新型节水冲击器-风动钢球冲击器和液动冲击器的结构设计、工作原理进行了研究。结果表明,这两种新型节水冲击器的应用不仅能够大量节约钻探过程中的用水量,而且能够大幅度提高钻探效率,在干旱缺水地区具有广泛推广应用前景。

关键词: 干旱缺水地区, 节水冲击器, 工作原理, 试验效果

Abstract: The present situation of many areas lack water seriously in China and execution of strategy of national geology survey makes it become urgent assignment that how to drill soft-middle hard rock rapidly and with high efficiency encountered frequently in drought and water-scarce area. The authors studied the structural design and the working principle of two new types of water-saving percussion tools, water-saving hydro-percussive tools and pneumatic steel ball percussion tools. The results showed that the application of the two new types of water-saving percussion tools can not only saved a lot of water during the course of drilling, but also improved drilling efficiency greatly, and had developing prospect in drought and water-scarce area.

Key words: drought and water-scarce area, water-saving percussion tools, working principle, tests result

中图分类号: 

  • P634.4
[1] 王传留,李建军,孙荣军. 孕镶块式高胎体金刚石钻头的研制[J]. 吉林大学学报(地球科学版), 2014, 44(4): 1276-1281.
[2] 范黎明, 殷琨, 张晓光, 王传留, 赵志强, 赵睿智, 朴金石. 潜孔锤钻进孔口密封器流场数值模拟及优化设计[J]. J4, 2011, 41(2): 511-517.
[3] 张永光, 彭枧明, 柳鹤, 殷其雷, 范黎明. 射流式液动锤活塞回程缓冲机构[J]. J4, 2010, 40(6): 1415-1418.
[4] 王传留, 孙友宏, 高科, 范黎明. 金刚石钻头可再生水口的试验[J]. J4, 2010, 40(3): 694-698.
[5] 何龙飞, 孙友宏, 高科, 刘宝昌, 徐良, 王传留. 仿生非光滑螺旋钻头的设计及试验[J]. J4, 2009, 39(2): 300-0304.
[6] 刘三意,夏柏如. 多工艺旋挖钻进施工钻具及在冻土层中的应用[J]. J4, 2008, 38(3): 460-0462.
[7] 郑治川,殷 琨,王清岩,彭枧明,苏继军. QFGZ型潜孔锤反循环跟管钻头的研制[J]. J4, 2007, 37(5): 1052-1054.
[8] 索忠伟,殷琨,徐克里,于平. 射流式液动锤内部动力过程的数学模型及仿真分析[J]. J4, 2007, 37(1): 200-0203.
[9] V.P.Onischin,陈 晨,赵秉成,朱 英. 新式整体不提钻切削具可换式钻头[J]. J4, 2006, 36(02): 309-0312.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!