吉林大学学报(工学版) ›› 2015, Vol. 45 ›› Issue (3): 788-796.doi: 10.13229/j.cnki.jdxbgxb201503016

Previous Articles     Next Articles

Experimental investigation of Σ-section channel steel with complex edge stiffeners and web holes under axial compression

WANG Chun-gang, ZHANG Zhuang-nan, ZHAO Da-qian, CAO Yu-fei   

  1. College of Civil Engineering, Shenyang Jianzhu University, Shenyang 110168, China
  • Received:2013-10-28 Online:2015-05-01 Published:2015-05-01

Abstract: The axial bearing capacity of thin-walled steel members with web holes and different section shapes are investigated. Ten simply supported compression members with two types of complicated sections, including channels with complex edge stiffeners and web holes, channels with complex edge stiffeners and Σ type web stiffeners and web holes, were tested. Results show that the axial compression loading efficiency of the Σ-section specimens with web holes can increase about 30% to 50% compared with channels with complex edge stiffeners and web holes under the same conditions. Compared with the specimens without holes, there is no change in failure modes, but the failure positions are near to the holes. Finite Element Analysis (FEA) is carried out to simulate the compression tests. FEA results agree well with the experimental data. Based on this, the load carrying efficiency and Von Mises stress distribution of channel columns with web holes are compared with those without holes by FEA. It is shown that the carrying efficiency of Σ-section models with holes decreases by 25.7% compared with the same section models without holes, while the model of channel section with complex edge stiffeners and holes decreases by 6.15% in average. Because of the perforations on the web, the positions of the stress concentration and the maximum stress change from the webs near the mid-height of the models to the locations adjacent to the holes.

Key words: civil engineering structure, web holes, channels with complex edge stiffeners and Σ, type web stiffeners, axial compression

CLC Number: 

  • TU392.1
[1] Narayanan S, Mahendran M. Ultimate capacity of innovative cold-formed steel columns[J]. Journal of Constructional Steel Research, 2003, 59 (4): 489-508.
[2] Moen C D, Schafer B W. Experiments on cold-formed steel columns with holes[J]. Thin-Walled Structures, 2008, 46(10): 1164-1182.
[3] Moen C D, Schafer B W. Direct strength method for design of cold-formed steel columns with holes[J]. Journal of Structural Engineering, 2010, 137(5): 559-570.
[4] 姚永红, 武振宇, 成博, 等. 开孔冷弯薄壁卷边槽钢柱轴压性能的试验研究[J]. 华南理工大学学报: 自然科学版, 2011, 39(9): 61-67.
Yao Yong-hong, Wu Zhen-yu, Cheng Bo, et al. Experimental investigation into axial compressive behavior of cold-formed thin-walled steel columns with lipped channel and openings[J]. Journal of South China University of Technology(Natural Science Edition), 2011,39(9): 61-67.
[5] Yang D, Hancock G J. Compression tests of high strength steel channel columns with interaction between local and distortional buckling[J]. Journal of Structural Engineering, 2004, 130(12): 1954-1963.
[6] 姚行友,李元齐,沈祖炎. 高强冷弯薄壁型钢卷边槽形截面轴压构件畸变屈曲性能研究[J]. 建筑结构学报, 2010, 31(11): 1-9.
Yao Xing-you, Li Yuan-qi, Shen Zu-yan. Distortional buckling behavior of high-strength cold-formed thin-walled steel lipped channel columns under axial compression[J]. Journal of Building Structures, 2010, 31(11): 1-9.
[7] Galambos T V. Guide to Stability Design Criteria for Metal Structures[M]. 5th ed. New York: John Wiley and Sons, 1998.
[8] 王春刚. 单轴对称冷弯薄壁型钢受压构件稳定性能分析与试验研究[D]. 哈尔滨: 哈尔滨工业大学土木工程学院, 2007.
Wang Chun-gang. Stability behavior analysis and experimental study on singly-symmetric cold-formed thin-walled steel members under compression loading[D]. Harbin: College of Civil Engineering,Harbin Institute of Technology, 2007.
[9] Kwon Y B, Hancock G J. Tests of cold-formed channels with local and distortional buckling[J]. Journal of Structural Engineering, 1992, 117(7): 1786-1803.
[10] Mulligan G P. The influence of local buckling on the structural behavior of singly-symmetric cold-formed steel columns[R]. Report No.83-1. Ithaca: Cornell University, 1983.
[11] 王春刚,张壮南,张耀春. 中间加筋复杂卷边槽钢轴心受压构件承载力试验研究[J]. 工程力学, 2013, 30(1): 221-228, 254.
Wang Chun-gang, Zhang Zhuang-nan, Zhang Yao-chun. Experimental investigation on channel columns with complex edge stiffeners and intermediate stiffeners under axial compression[J].Engineering Mechanics, 2013, 30(1): 221-228, 254.
[12] Zhang Yao-chun, Wang Chun-gang, Zhang Zhuang-nan. Tests and finite element analysis of pin-ended channel columns with inclined simple edge stiffeners[J]. Journal of Constructional Steel Research, 2007, 63(3): 383-395.
[13] 库克R D.有限元分析的概念和应用[M]. 程耿东译.北京:科学出版社,1989.
[14] Dubina D, Ungureany V. Effect of imperfections on numerical simulation of instability behaviour of cold-formed steel members[J]. Thin-Walled Structures, 2002, 40(3): 239-262.
[15] 马平. 新型截面冷弯薄壁型钢轴心受压构件稳定性能研究[D]. 沈阳: 沈阳建筑大学土木工程学院, 2012.
Ma Ping. The stability behavior of cold-formed thin-walled steel members with new cross sections under compression loading[D]. Shenyang: College of Civil Engineering,Shenyang Jianzhu University, 2012.
[1] NI Ying-sheng, SUN Qi-xin, MA Ye, XU Dong. Calculation of capacity reinforcement about composite box girder with corrugated steel webs based on tensile stress region theory [J]. 吉林大学学报(工学版), 2018, 48(1): 148-158.
[2] LIU Han-bing, ZHANG Hu-zhu, WANG Jing. Effect of dehydration on shear strength properties of compacted clayey soil [J]. 吉林大学学报(工学版), 2017, 47(2): 446-451.
[3] ZHANG Yan-ling, SUN Tong, HOU Zhong-ming, LI Yun-sheng. Bending-torsion characteristics of steel-concrete curved composite beams stiffened with diaphragms [J]. 吉林大学学报(工学版), 2015, 45(4): 1107-1114.
[4] LI Hai-feng,GUO Xiao-nong,LUO Yong-feng,GAO Xuan-neng. Collapse resistance behavior of Ferris wheel with stay cables [J]. 吉林大学学报(工学版), 2015, 45(2): 406-413.
[5] GUO Jun-ping, DENG Zong-cai, LU Hai-bo, LIN Jin-song. Experiment on shear behavior of reinforced concrete beams strengthened with prestressed high strength steel wire mesh [J]. 吉林大学学报(工学版), 2014, 44(4): 968-977.
[6] JIANG Feng-guo, ZHAO Jing-lu. Reliability analysis of reinforced concrete member under fire load [J]. 吉林大学学报(工学版), 2013, 43(06): 1500-1503.
[7] LI Li-ming,CHEN Yi-yi,LI Ning,CAI Yu-chun. Seismic performance of outer-shell connection of cold-formed square tubular column and H-shaped steel beam [J]. 吉林大学学报(工学版), 2010, 40(01): 67-0071.
[8] SHI Gang,SHI Yong-jiu,WANG Yuan-qing . Analysis on overall buckling behaviour of ultra-high strength steel columns by ANSYS [J]. 吉林大学学报(工学版), 2009, 39(01): 113-118.
[9] ZHANG Su-mei, YUN Di . Lateral brace arrangement for large-span half-through concrete filled steel tube arch bridge [J]. 吉林大学学报(工学版), 2009, 39(01): 108-112.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!