吉林大学学报(工学版) ›› 2015, Vol. 45 ›› Issue (6): 1836-1843.doi: 10.13229/j.cnki.jdxbgxb201506016

Previous Articles     Next Articles

Processing technology of face gear complex surface based on bus control

WANG Yan-zhong1, HOU Liang-wei1, LYU Qing-jun2, ZHAO Xing-fu3, WU Can-hui4   

  1. 1.College of Mechanical Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191,China;
    2.China North Vehicle Research Institute, Beijing 100072,China;
    3.AVIC Harbin Dong'an Engine Corporation LTD., Harbin 150066,China;
    4.China Aero-polytechnology Establishment, Beijing 100028,China
  • Received:2014-04-21 Online:2015-11-01 Published:2015-11-01

RICH HTML

0   

PDF (PC)

495

Abstract: A control method for five-axle linkage CNC machine tools was proposed based on EtherCAT, and special CNC processing equipment for face gear was developed. The principles and methods of hopping and milling were analyzed on the basis of the principle of face gear cutting. The CNC processing coordinate conversion and tool path generation of hopping and milling were conducted. The CNC methods of processing were given based on the structure of the special face gear machine, and processing experiments of face gear were conducted. The coordinate values of tooth surface points were detected by pmm-c700 CMM, and the deviation ranges in the normal direction of face gear surface were obtained. The results verify that the structure of the machine and the processing methods are feasible, which lay the foundation of engineering applications of face gears.

Key words: machinery manufacturing automation, face gear processing, bus control, tool path generation, experimental verification

CLC Number: 

  • TG659
[1] Litvin F L. Face gear drive with helical involute pinion: geometry, generation by a shaper and a worm, avoidance of singularities and stress analysis[R].Washington:NASA,2005.
[2] Chen Y D, Bossler R B. Design analysis and testing methods for a split torque face-gear transmission[C]∥31th AIAA/SAE/ASME/ASEE Joint Propulsion Conference and Exhibit,San Diego,CA,1995:1-7.
[3] Lewicki D G, Dempsey P J, Heath F G, et al. Gear fault detection effectiveness as applied to tooth surface pitting fatigue damage[R].Washington: NASA, 2007.
[4] Litvin F L. Gear Geometry and Applied Theory[M]. New jersey: PTR Prentice Hall, 1994.
[5] Hermann D, Stadtfeld J. CONIFACE face gear cutting and grinding[J]. Gear Solutions,2010(9):38-47.
[6] Lewichi D G, Heath G F, Filler R R, et al. RDS-21 face gear surface durability tests[R]. American Helicopter Society International Forum, ARL-TR-4089,2007.
[7] Guingand M, Vaujany J P, Jaquin C Y. Quasi-static analysis of a face gear under torque[J].Computer Methods in Applied Mechanics and Engineering,2005,194(39-41): 4301-4318.
[8] 朱如鹏, 高德平. 面齿轮传动的研究现状与发展[J]. 南京航空航天大学学报,1997,29(3):357-362.
Zhu Ru-peng, Gao De-ping. Current state and development of research on face gear drive[J]. Journal of Nanjing University of Aeronautics and Astronautics,1997,29(3):357-362.
[9] Zhao Ning, Guo Hui, Fang Zong-de, et al. Research on machining face gear using a CNC hobbing machine[J]. Advanced Materials Research,2010,97(101):3761-3764.
[10] 赵宁, 郭辉, 方宗德, 等. 用球形滚刀滚切面齿轮的理论误差[J]. 航空动力学报,2009,24(3):677-682.
Zhao Ning, Guo Hui, Fang Zong-de, et al. Theory error of cutting face gears with sphericity hob[J]. Journal of Aerospace Power,2009,24(3):677-682.
[11] 李大庆. 直齿面齿轮啮合性能预控及碟形砂轮磨齿关键技术研究[D]. 镇江:江苏大学机械工程学院,2013.
Li Da-qing. Research on precontrol method of meshing behavior and key technologies for grinding face gear by dish wheel[D]. Zhenjiang: School of Mechanical Engineering, Jiangsu University, 2013.
[12] 王延忠, 吴灿辉, 葛旭阳. 面齿轮滚刀基本蜗杆的设计方法[J]. 北京航空航天大学学报, 2009,35(2):166-169.
Wang Yan-zhong, Wu Can-hui, Ge Xu-yang. Basalworm designing method of face gear hob[J]. Journal of Beijing University of Aeronautics and Astronautics, 2009,35(2):166-169.
[13] Wang Yan-zhong, Hou Liang-wei, Liu Yan-qing, et al. Research on machining method of complex surface face gears[J]. Applied Mechanics and Materials,2012,163:233-237.
[14] 刘清建, 王太勇, 徐跃, 等. 基于总线架构的多层次监控开放数控系统[J]. 吉林大学学报:工学版,2010,40(6): 1589-1594.
Liu Qing-jian, Wang Tai-yong, Xu Yue, et al. Multilayer monitoring and open CNC system based on fieldbus[J]. Journal of Jilin University(Engineering and Technology Edition),2010, 40(6):1589-1594.
[15] 吴坚, 李亚彬, 李静, 等. 基于SAEJ1939协议的汽车驱动力控制CAN总线[J]. 吉林大学学报:工学版,2009,39(4):855-858.
Wu Jian,Li Ya-bin,Li Jing,et al.CAN bus of automotive driving force control system based on SAE protocol J1939[J].Journal of Jilin University(Engineering and Technology Edition),2009,39(4):855-858.
[1] MA Wen-xing, ZHANG Yan, LEI Yu-long. Design and test of control system of hydrodynamic automotive transmission for heavy vehicle [J]. 吉林大学学报(工学版), 2015, 45(5): 1455-1460.
[2] on improved EM algorithm. Reliability modeling of finite Weibull distribution based [J]. 吉林大学学报(工学版), 2014, 44(4): 1010-1015.
[3] YANG Zhao-jun,WANG Ji-li,LI Guo-fa,ZHANG Xin-ge. Reliability growth prediction based on fuzzy analytical hierarchy process for punching machines [J]. 吉林大学学报(工学版), 2014, 44(3): 686-691.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
Copyright © Journal of Jilin University(Engineering and Technology Edition), All Rights Reserved.
Tel: +86-431-85095297　Fax: +86-431-85094074　E-mail: xbgxb@jlu.edu.cn
Powered by Beijing Magtech Co. Ltd