吉林大学学报(工学版)

• • 上一篇    下一篇

TC4/QAL10-3-1.5直接扩散连接形貌分析

郭伟1,赵熹华1,宋敏霞1,冯吉才2,杨飚1   

  1. 1.吉林大学 材料科学与工程学院,长春 130022; 2. 哈尔滨工业大学 现代焊接生产技术国家重点实验室, 哈尔滨 150001
  • 收稿日期:2005-09-04 修回日期:2005-11-20 出版日期:2006-05-01 发布日期:2006-05-01
  • 通讯作者: 赵熹华

Pattern analysis on diffusion bonding of TC4 and QAL1031.5

Guo Wei1, Zhao Xi-hua1, Song Min-xia1,Feng Ji-cai2,Yang Biao1   

  1. 1.College of Materials Science and Engineering, Jilin University, Changchun 130022, China; 2. National Key Laboratory of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin 150001, China
  • Received:2005-09-04 Revised:2005-11-20 Online:2006-05-01 Published:2006-05-01
  • Contact: Zhao Xihua

摘要: 对TC4/QAL1031.5直接扩散连接的研究表明:在连接温度T=850 ℃、连接压力P=8 MPa、保温时间t=30 min的条件下,能够实现接头的扩散连接,然而在扩散接头的局部有裂纹产生。利用扫描电镜对扩散接头进行了显微组织分析,利用能谱仪对扩散接头的元素扩散距离和浓度分布进行了分析。结果表明:形成了厚度为10 μm的扩散接头,元素扩散距离与保温时间之间满足抛物线规律x2=Kp(t-t0);由于Cu与Ti 的扩散系数不同,导致发生扩散接头向TC4方向偏移的克肯达尔现象。利用界面孔洞理论解释了裂纹产生的机理,提出了工艺改进的方法,并获得了较好的效果。

关键词: 材料合成及加工工艺, 扩散连接, 裂纹, 微观组织, 铜合金, 钛合金

Abstract: Diffusion bonding of TC4 and QAL1031.5 was carried out under the condition of 850 ℃, 8 MPa and 30 min, but there are cracks existing on local area of diffusion zone. Microstructure of diffusion zone was analyzed using scanning electron microscopy (SEM), and diffusion distance and concentration distribution of elements were analyzed using EDS. The result shows that the transition zone thickness is 10 μm. Diffusion distance of element increases with increasing bonding time followed a parabolic law: x2=Kp(t-t0), and phenomenon of transition zone moving to TC4 are observed which is so called kirkendall effect . The occurrence of the cracks on the diffusion zone was studied in the theory of interfrcial pore and the reason for microcracks produced and improvement methods are found out. Thus, approving diffusion joint is attained by improving the welding process.

Key words: materials synthesis and processing technology, diffusion bonding, crack, microstructure, copper alloy, titanium alloy

中图分类号: 

  • TG457.1
[1] 郑孝义, 孙大千, 李欣, 都桂刚, 辛伟达, 任振安. NbAl3强化Al-Nb熔覆层的组织与性能[J]. 吉林大学学报(工学版), 2018, 48(5): 1531-1536.
[2] 孟广伟, 李荣佳, 王欣, 周立明, 顾帅. 压电双材料界面裂纹的强度因子分析[J]. 吉林大学学报(工学版), 2018, 48(2): 500-506.
[3] 王腾, 周茗如, 马连生, 乔宏霞. 基于断裂理论的湿陷性黄土劈裂注浆裂纹扩展[J]. 吉林大学学报(工学版), 2017, 47(5): 1472-1481.
[4] 谷晓燕, 刘亚俊, 孙大千, 徐锋, 孟令山, 高帅. S355钢/6005A铝合金瞬间液相扩散连接接头组织与性能[J]. 吉林大学学报(工学版), 2017, 47(5): 1534-1541.
[5] 曹珊珊, 雷俊卿. 考虑区间不确定性的钢结构疲劳寿命分析[J]. 吉林大学学报(工学版), 2016, 46(3): 804-810.
[6] 杨慧艳, 何晓聪, 周森. 压印接头强度的有限元模型及理论计算方法[J]. 吉林大学学报(工学版), 2015, 45(3): 864-871.
[7] 李欣,王刚,陆冠含,谷诤巍,徐虹. 22MnB5热成形钢板钨极氩弧焊接性能[J]. 吉林大学学报(工学版), 2014, 44(3): 708-711.
[8] 王元清, 林云, 张延年, 石永久. 高强度钢材Q460C断裂韧性低温试验 [J]. , 2012, (03): 639-644.
[9] 谷诤巍, 于思彬, 韩立军, 孟佳, 沈永波, 徐虹. 激光焊接速度对超高强度钢焊缝微观组织和显微硬度的影响 [J]. , 2012, (03): 656-659.
[10] 杨冬风, 马秀莲. 基于分形纹理分析的蛋壳裂纹识别[J]. 吉林大学学报(工学版), 2011, 41(增刊1): 348-352.
[11] 汪洪峰,左敦稳,王珉,缪宏. 5554铝合金异种焊料焊接的显微组织及力学性能[J]. 吉林大学学报(工学版), 2011, 41(4): 974-977.
[12] 赵勇,杨慎华,郑祺峰,金文明. 激光预制裂纹槽的断裂分析[J]. 吉林大学学报(工学版), 2011, 41(4): 984-987.
[13] 彭惠芬1,2,孟广伟1,周立明1,李锋1. 基于小波有限元法的虚拟裂纹闭合法[J]. 吉林大学学报(工学版), 2011, 41(05): 1364-1368.
[14] 卢广林,邱小明, 白杨,伦辛杰,邓宝清,任露泉. c-BN仿生耐磨复合材料的微观结构和耐磨性能[J]. 吉林大学学报(工学版), 2011, 41(01): 73-0077.
[15] 于鸣, 于思彬, 张正林, 谷诤巍. 超高强度钢激光焊接的微观组织与断口分析[J]. 吉林大学学报(工学版), 2010, 40(增刊): 239-0242.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!