22MnB5超高强钢焊接接头强化性能

doi:10.13229/j.cnki.jdxbgxb20170617

摘要/Abstract

摘要：

以22MnB5超高强钢淬火状态焊接接头为研究对象,进行了焊接过程中的机械旋压强化处理工艺试验,测试并分析了焊接接头的力学性能、显微组织和显微硬度耐蚀性。结果表明:焊接接头经过机械旋压后,会在接头表面形成一层塑性变形层,晶粒在压头旋压的作用下会被压扁拉长,其分布会更加均匀致密;焊接接头抗拉强度会达到940 MPa左右,相对未处理的焊接接头抗拉强度提高了约100 MPa,其显微硬度有小幅增加,但耐蚀性能变化不大。

关键词: 材料合成与加工工艺, 22MnB5钢, 力学性能, 显微组织

Abstract:

The 22MnB5 ultra high strength steel quenching joint in state welding is taken as the research object, intensive processing experiments are carried out in spinning machinery in the process of welding. The mechanical properties of the welded joints, microstructure, microhardness, corrosion resistance are tested and analyzed. The results show that the welding joint after mechanical spinning, a plastic deformation layer is formed on the joint surface. The grains in the head spinning are flattened and elongated and the grain distribution is more uniform. The tensile strength of welded joint is about 940 MPa, which is about 100 MPa higher than that of untreated welded joints. The microhardness is slightly increased, but the corrosion resistance is changed little.

Key words: materials synthesis and processing technology, 22MnB5 steel, mechanical properties, microstructure

中图分类号:

TG453

姜秋月,杨海峰,檀财旺. 22MnB5超高强钢焊接接头强化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1806-1810.

JIANG Qiu-yue,YANG Hai-feng,TAN Cai-wang. Strengthening properties of welded joints of 22MnB5 super high strength steel[J]. Journal of Jilin University(Engineering and Technology Edition), 2018, 48(6): 1806-1810.

图/表 6

表1

图1

图2

图3

图4

图5

参考文献 9

[1]	操志博, 贾耿伟, 王连轩 , 等. 热冲压用超高强钢22MnB5性能测试与分析[J]. 河北冶金, 2017(3):9-14. doi: 10.13630/j.cnki.13-1172.2017.0302
	Cao Zhi-bo, Jia Geng-wei, Wang Lian-xuan , et al. Performance testing and analysis of super high strength steel 22MnB5 for hot stamping[J]. Hebei Metallurgy, 2017(3):9-14. doi: 10.13630/j.cnki.13-1172.2017.0302
[2]	Min Jun-ying, Lin Jian-ping, Li Jia-yue , et al. Investigation on hot forming limits of high strength steel 22MnB5[J]. Computational Material Science, 2014,49(2):326-332. doi: 10.1016/j.commatsci.2010.05.018
[3]	刘如红, 符月虹 . 超高强钢板热冲压成形工艺及装备的研究[J]. 液压气动与密封, 2015(6):54-56. doi: 10.3969/j.issn.1008-0813.2015.06.019
	Liu Ru-hong, Fu Yue-hong . Research on super-high strong steel plate hot stamping forming technology and equipment[J]. Hydraulic and Pneumatic Seals, 2015(6):54-56. doi: 10.3969/j.issn.1008-0813.2015.06.019
[4]	Naderi M, Uthaisangsuk V, Prahl U , et al. Numerical and experimental investigation into hot stamping of boron alloyed heat treated steels[J]. Steel Research International, 2014,79(2):77-84. doi: 10.1002/srin.200806320
[5]	Altan T . Hot stamping boron-alloyed steels for automotive parts—partII[J]. Stamping Journal, 2014(12):40-41.
[6]	Kerstens N F H, Richardson I M . Heat distribution in resistance upset butt welding[J]. Journal of Materials Processing Technology, 2014,209(5):2715-2722. doi: 10.1016/j.jmatprotec.2008.06.015
[7]	吴斌, 曹志福 . 超高强钢板U形件热冲压回弹研究[J]. 热加工工艺, 2016(11):140-143.
	Wu Bin, Cao Zhi-fu . Study on hot stamping springback of super high strength steel sheet U[J]. Hot Working Technology, 2016(11):140-143.
[8]	Muccillo R, Muccillo E N S, Kleitz M . Densification and enhancement of the grain boundary conductivity of gadolinium-doped barium cerate by ultra fast flash grain welding[J]. Journal of the European Ceramic Society, 2014,32(10):2311-2316. doi: 10.1016/j.jeurceramsoc.2012.01.032
[9]	Li Bo, Zhang Zhen-hua, Shen Yi-fu , et al. Dissimilar friction stir welding of Ti-6Al-4V alloy and aluminum alloy employing a modified butt joint configuration: influences of process variables on the weld interfaces and tensile properties[J]. Materials and Design, 2013,53:838-848.

相关文章 15

[1]	胡志清, 颜庭旭, 李洪杰, 吕振华, 廖伟, 刘庚. 深冷处理对铝合金薄板冲剪成形性能的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1524-1530.
[2]	庄蔚敏, 赵文增, 解东旋, 李兵. 超高强钢/铝合金热铆连接接头性能[J]. 吉林大学学报(工学版), 2018, 48(4): 1016-1022.
[3]	邱小明, 王银雪, 姚汉伟, 房雪晴, 邢飞. 基于灰色关联的DP1180/DP590异质点焊接头工艺参数优化[J]. 吉林大学学报(工学版), 2018, 48(4): 1147-1152.
[4]	陈俊甫, 管志平, 杨昌海, 牛晓玲, 姜振涛, 宋玉泉. 金属棒试样拉伸和扭转试验应变范围和力学特性对比[J]. 吉林大学学报(工学版), 2018, 48(4): 1153-1160.
[5]	梁晓波, 蔡中义, 高鹏飞. 夹芯复合板柱面成形的数值模拟及试验[J]. 吉林大学学报(工学版), 2018, 48(3): 828-834.
[6]	刘子武, 李剑峰. 叶片材料FV520B再制造熔覆层冲蚀损伤行为及评价[J]. 吉林大学学报(工学版), 2018, 48(3): 835-844.
[7]	赵宇光, 杨雪慧, 徐晓峰, 张阳阳, 宁玉恒. Al-10Sr变质剂状态、变质温度及变质时间对ZL114A合金组织的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 212-220.
[8]	刘纯国, 刘伟东, 邓玉山. 多点冲头主动加载路径对薄板拉形的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 221-228.
[9]	张志强, 刘从豪, 何东野, 李湘吉, 李纪萱. 基于性能梯度分布的硼钢热冲压工艺对形状精度的影响[J]. 吉林大学学报(工学版), 2017, 47(6): 1829-1833.
[10]	吕萌萌, 谷诤巍, 徐虹, 李欣. 超高强度防撞梁热冲压成形工艺优化[J]. 吉林大学学报(工学版), 2017, 47(6): 1834-1841.
[11]	王辉, 周杰, 熊煜, 陶亚平, 向荣. 基于逆向工程的复杂曲面冲压件回弹补偿[J]. 吉林大学学报(工学版), 2017, 47(6): 1842-1847.
[12]	王春生, 邹丽, 杨鑫华. 基于邻域粗糙集的铝合金焊接接头疲劳寿命影响因素分析[J]. 吉林大学学报(工学版), 2017, 47(6): 1848-1853.
[13]	邢海燕, 葛桦, 李思岐, 杨文光, 孙晓军. 基于模糊隶属度最大似然估计的焊缝隐性缺陷磁记忆信号识别[J]. 吉林大学学报(工学版), 2017, 47(6): 1854-1860.
[14]	谷晓燕, 刘亚俊, 孙大千, 徐锋, 孟令山, 高帅. S355钢/6005A铝合金瞬间液相扩散连接接头组织与性能[J]. 吉林大学学报(工学版), 2017, 47(5): 1534-1541.
[15]	谷诤巍, 张文学, 吕萌萌, 王伟, 徐虹, 李欣. 宽翼边U型截面不锈钢型材拉弯成形缺陷控制[J]. 吉林大学学报(工学版), 2017, 47(4): 1165-1170.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed

材料	抗拉强度σ_b/MPa	屈服强度σ_s/MPa	断后伸长率δ/%
原始钢板	502.27	354.62	26.4
淬火钢板	1725.57	-	3.52