吉林大学学报(工学版) ›› 2018, Vol. 48 ›› Issue (3): 835-844.doi: 10.13229/j.cnki.jdxbgxb20170189

• 论文 • 上一篇    下一篇

叶片材料FV520B再制造熔覆层冲蚀损伤行为及评价

刘子武1,2, 李剑峰1,2   

  1. 1.山东大学 机械工程学院,济南 250061;
    2.山东大学 机械工程国家级实验教学示范中心,济南250061;
  • 收稿日期:2017-03-05 出版日期:2018-05-20 发布日期:2018-05-20
  • 通讯作者: 李剑峰(1963-),男,教授,博士生导师.研究方向:机械加工,绿色制造与再制造.E-mail:ljf@sdu.edu.cn
  • 作者简介:刘子武(1985-),男,博士研究生.研究方向:机械加工,绿色制造与再制造.E-mail:liuziwu1985@163.com
  • 基金资助:
    “973”国家重点基础研究发展计划项目(2011CB013401).

Erosion damage and evaluation of remanufacturing cladding layer for impeller metals FV520B

LIU Zi-wu1,2, LI Jian-feng1,2   

  1. 1.School of Mechanical Engineering, Shandong University, Jinan 250061, China;
    2.National Demonstration Center for Experimental Mechanical Engineering Education, Shandong University, Jinan 250061,China
  • Received:2017-03-05 Online:2018-05-20 Published:2018-05-20

摘要: 利用激光熔覆和钨极氩弧(TIG)熔覆技术在FV520B钢表面制备与材料成分相同的熔覆层,并对TIG熔覆层分别进行470 °C和615 °C回火,分析了熔覆层的微观组织、抗冲蚀能力及冲蚀后的熔覆层表面特性。试验结果表明:激光熔覆层均匀致密,平均显微硬度最高;回火TIG熔覆层性能与母材相似。随着硬度提高,冲蚀率最高点向高角度方向移动。冲蚀角度小于30°时,激光熔覆层抗冲蚀性能及表面粗糙度较好;高角度冲蚀时,激光熔覆层冲蚀率高于回火TIG熔覆层。在冲蚀率最高的角度附近,冲蚀硬化程度最低,正向冲蚀下的硬化程度最高。熔覆层越硬,冲蚀产生的残余拉、压应力越高。

关键词: 材料合成与加工工艺, 熔覆层冲蚀评价, 显微组织, 粗糙度, 冲蚀硬化, 残余应力

Abstract: Coating layer with the same composition as the FV520B steel was deposited on the base material by laser cladding and Tungsten Inert Gas (TIG) cladding. Then, TIG cladding was tempered at 470 °C and 615 °C, respectively. The microstructure, hardness, erosion resistance of the cladding layers were investigated, and the surface quality, micro-hardness and residual stress were also tested after erosion. The results show that laser cladding with compact and symmetrical microstructure has the highest hardness, and TIG cladding with tempering has similar microstructure compared with the base material. With the increase in hardness, the erosion peak will move towards the high angle. When the impacting angle is less than 30°, the anti-erosion performance and surface quality of the laser cladding are better. At higher impacting angle, anti-erosion performance the laser cladding is worse than that of TIG cladding layer. For all the layers, erosion hardness is the lowest at the impacting angle with highest erosion rate, and erosion hardness is highest at the impacting angle of 90°. Both residual extend stress and residual compressive stress, which are caused by erosion, are maximal for laser cladding layer with highest hardness.

Key words: materials synthesis and processing technology, erosion evaluation of cladding layer, microstructural, surface roughness, erosion hardening, residual stress

中图分类号: 

  • TB31
[1] Utamura M,Fukuda T,Aritomii M.Aerodynamic characteristics of a centrifugal compressor working in supercritical carbon dioxide[J].Energy Procedia,2012,14:1149-1155.
[2] 舒林森,曹华军,许磊,等. 离心压缩机再制造叶轮结构特征三维建模方法及应用[J].机械工程学报,2014,50(3):184-190.
Shu Lin-sen,Cao Hua-jun,Xu Lei,et al.3D characteristic modeling method and application for remanufactured impeller of centrifugal compressor[J]. Journal of Mechanical Engineering,2014,50(3):184-190.
[3] Nakhaei R, Khodabandeh A, Najafi H.Effect of active gas on weld shape and microstructure of advanced A-TIG-Welded stainless steel[J]. Acta Metallurgica Sinica,2016,29(3):295-300.
[4] 徐滨士,刘世参,史佩京. 再制造工程和表面工程对循环经济贡献分析[J]. 中国表面工程,2006,19(1):1-6.
Xu Bin-shi,Liu Shi-can,Shi Pei-jing.Contribution of remanufacturing engineering and surface engineering to cycle economy[J].China Surface Engineering,2006,19(1):1-6.
[5] 周圣丰,戴晓琴,郑海忠. 激光熔覆与激光-感应复合熔覆WC-Ni60A 涂层的结构与性能特征[J]. 机械工程学报,2012,48(7):113-118.
Zhou Sheng-feng,Dai Xiao-qin,Zheng Hai-zhong.Characteristics on structure and properties of WC-Ni60A coatings by laser cladding and laser-induction hybrid clading[J]. Journal of Mechanical Engineering,2012,48(7):113-118.
[6] Rottwinkel B, Nölke C,Kaierle S,et al.Crack repair of single crystal turbine blades using laser cladding technology[J]. Procedia Cirp,2014,22(1):263-267.
[7] Xu Lei,Cao Hua-jun,Liu Hai-long,et al.Study on laser cladding remanufacturing process with FeCrNiCu alloy powder for thin-wall impeller blade[J]. The International Journal of Advanced Manufacturing Technology,2017,90(5-8):1383-1392.
[8] 黄薇. 激光熔覆技术在空压机叶轮修复上的应用[J]. 化工机械,2011,38(3):355-356.
Huang Wei.Laser cladding for repairing air compressor impellers[J]. Chemical Engineering & Machinery,2011,38(3):355-356.
[9] 姚建华,叶钟,沈红卫. 激光加工技术在汽轮机叶片制造中的应用[J]. 激光与光电子学进展,2012,49(3):104-109.
Yao Jian-hua,Ye Zhong,Shen Hong-wei.Application of laser processing technologies on turbine blades[J]. Laser & Optoelectronics Progress,2012,49(3):104-109.
[10] Wei Z,Yao J H,Dong C H,et al.Repairing and strengthening of eroded turbine blades by laser technology[J]. Journal of Power Engineering,2008,28(6):967-971.
[11] 余冬梅. 激光熔覆Stellite6/TiCN复合涂层的组织及性能研究[D]. 兰州:兰州理工大学材料学院,2014.
Yu Dong-mei.Investigation on microstructure and properties of Stellite6/TiCNcomposite coating by laser cladding[D]. Lanzhou: College of Materials, Lanzhou University of Technology,2014.
[12] 王璐,胡树兵,单炜涛,等. 激光熔覆NiCrMn-WC复合涂层的组织与耐磨性[J]. 中国有色金属学报,2014(1):145-151.
Wang Lu,Hu Shu-bing,Shan Wei-tao,et al. Microstructure and wear resistance of laser cladding NiCrMn-WC composite coatings[J]. The Chinese Journal of Nonferrous Metals, 2014(1):145-151.
[13] 李剑峰,王光存,刘子武,等. 一种气流喷砂式冲蚀磨损试验机[P]. 中国:CN103760048A,2014-04-30.
[14] 余永宁. 金属学原理[M].北京:冶金工业出版社,2013:422-423.
[15] 王光存. 离心压缩机叶轮冲蚀磨损机理和规律的研究[D]. 济南:山东大学机械工程学院, 2015.
Wang Guang-cun.Study on erosion wear mechanism and law of impeller in centrifugal compressor[D]. Jinan:School of Mechanical Engineering, Shandong University,2015.
[16] 张明. 离心压缩机叶轮材料FV520B超高周疲劳行为与机理研究[D]. 济南:山东大学机械工程学院,2015.
Zhang Ming.Research on fatigue behavior and mechanism of FV520B in very high cycle regime[D]. Jinan:School of Mechanical Engineering, Shandong University,2015.
[17] Agrawal S,Joshi S S.Analytical modelling of residual stresses in orthogonal machining of AISI4340 steel[J]. Journal of Manufacturing Processes,2013,15(1):56-68.
[18] Byrne G D,O’NeillL,Twomey B,et al. Comparison between shot peening and abrasive blasting processes as deposition methods for hydroxyapatite coatings onto a titanium alloy[J]. Surface and Coatings Technology,2013,216:224-231.
[1] 姜秋月,杨海峰,檀财旺. 22MnB5超高强钢焊接接头强化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1806-1810.
[2] 赵爽,沈继红,张刘,赵晗,陈柯帆. 微细电火花加工表面粗糙度快速高斯评定[J]. 吉林大学学报(工学版), 2018, 48(6): 1838-1843.
[3] 胡志清, 颜庭旭, 李洪杰, 吕振华, 廖伟, 刘庚. 深冷处理对铝合金薄板冲剪成形性能的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1524-1530.
[4] 邱小明, 王银雪, 姚汉伟, 房雪晴, 邢飞. 基于灰色关联的DP1180/DP590异质点焊接头工艺参数优化[J]. 吉林大学学报(工学版), 2018, 48(4): 1147-1152.
[5] 陈俊甫, 管志平, 杨昌海, 牛晓玲, 姜振涛, 宋玉泉. 金属棒试样拉伸和扭转试验应变范围和力学特性对比[J]. 吉林大学学报(工学版), 2018, 48(4): 1153-1160.
[6] 梁晓波, 蔡中义, 高鹏飞. 夹芯复合板柱面成形的数值模拟及试验[J]. 吉林大学学报(工学版), 2018, 48(3): 828-834.
[7] 赵宇光, 杨雪慧, 徐晓峰, 张阳阳, 宁玉恒. Al-10Sr变质剂状态、变质温度及变质时间对ZL114A合金组织的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 212-220.
[8] 刘纯国, 刘伟东, 邓玉山. 多点冲头主动加载路径对薄板拉形的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 221-228.
[9] 张志强, 刘从豪, 何东野, 李湘吉, 李纪萱. 基于性能梯度分布的硼钢热冲压工艺对形状精度的影响[J]. 吉林大学学报(工学版), 2017, 47(6): 1829-1833.
[10] 吕萌萌, 谷诤巍, 徐虹, 李欣. 超高强度防撞梁热冲压成形工艺优化[J]. 吉林大学学报(工学版), 2017, 47(6): 1834-1841.
[11] 王辉, 周杰, 熊煜, 陶亚平, 向荣. 基于逆向工程的复杂曲面冲压件回弹补偿[J]. 吉林大学学报(工学版), 2017, 47(6): 1842-1847.
[12] 王春生, 邹丽, 杨鑫华. 基于邻域粗糙集的铝合金焊接接头疲劳寿命影响因素分析[J]. 吉林大学学报(工学版), 2017, 47(6): 1848-1853.
[13] 邢海燕, 葛桦, 李思岐, 杨文光, 孙晓军. 基于模糊隶属度最大似然估计的焊缝隐性缺陷磁记忆信号识别[J]. 吉林大学学报(工学版), 2017, 47(6): 1854-1860.
[14] 谷晓燕, 刘亚俊, 孙大千, 徐锋, 孟令山, 高帅. S355钢/6005A铝合金瞬间液相扩散连接接头组织与性能[J]. 吉林大学学报(工学版), 2017, 47(5): 1534-1541.
[15] 谷诤巍, 张文学, 吕萌萌, 王伟, 徐虹, 李欣. 宽翼边U型截面不锈钢型材拉弯成形缺陷控制[J]. 吉林大学学报(工学版), 2017, 47(4): 1165-1170.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 何磊,宗长富,田承伟,吴仁军,张太武. 线控转向汽车直流电机的故障诊断与容错控制[J]. 吉林大学学报(工学版), 2011, 41(03): 608 -612 .
[2] 刘松山, 王庆年, 王伟华, 林鑫. 惯性质量对馈能悬架阻尼特性和幅频特性的影响[J]. 吉林大学学报(工学版), 2013, 43(03): 557 -563 .
[3] 初亮, 王彦波, 祁富伟, 张永生. 用于制动压力精确控制的进液阀控制方法[J]. 吉林大学学报(工学版), 2013, 43(03): 564 -570 .
[4] 李静, 王子涵, 余春贤, 韩佐悦, 孙博华. 硬件在环试验台整车状态跟随控制系统设计[J]. 吉林大学学报(工学版), 2013, 43(03): 577 -583 .
[5] 胡兴军, 李腾飞, 王靖宇, 杨博, 郭鹏, 廖磊. 尾板对重型载货汽车尾部流场的影响[J]. 吉林大学学报(工学版), 2013, 43(03): 595 -601 .
[6] 王同建, 陈晋市, 赵锋, 赵庆波, 刘昕晖, 袁华山. 全液压转向系统机液联合仿真及试验[J]. 吉林大学学报(工学版), 2013, 43(03): 607 -612 .
[7] 张春勤, 姜桂艳, 吴正言. 机动车出行者出发时间选择的影响因素[J]. 吉林大学学报(工学版), 2013, 43(03): 626 -632 .
[8] 马万经, 谢涵洲. 双停车线进口道主、预信号配时协调控制模型[J]. 吉林大学学报(工学版), 2013, 43(03): 633 -639 .
[9] 于德新, 仝倩, 杨兆升, 高鹏. 重大灾害条件下应急交通疏散时间预测模型[J]. 吉林大学学报(工学版), 2013, 43(03): 654 -658 .
[10] 肖赟, 雷俊卿, 张坤, 李忠三. 多级变幅疲劳荷载下预应力混凝土梁刚度退化[J]. 吉林大学学报(工学版), 2013, 43(03): 665 -670 .