Journal of Jilin University(Engineering and Technology Edition) ›› 2022, Vol. 52 ›› Issue (4): 745-753.doi: 10.13229/j.cnki.jdxbgxb20200931

Previous Articles    

Optimization of the aerodynamic drag reduction of a cab behind engine vehicle

Ying-chao ZHANG(),Yun-hang LI,Zi-yu GUO,Guo-hua WANG,Zhe ZHANG(),Chang SU   

  1. State Key Laboratory of Automotive Simulation and Control，Jilin University，Changchun 130022，China
  • Received:2020-12-02 Online:2022-04-01 Published:2022-04-20
  • Contact: Zhe ZHANG E-mail:yingchao@jlu.edu.cn;zhangzhejlu@jlu.edu.cn

RICH HTML

 7   

PDF (PC)

142

Abstract:

In this paper, the cab behind engine vehicles are taken as the research object, and the entire aerodynamic performance optimization is carried out. The optimization is composed of two steps, the initial shape optimization of the molding surface in the early modeling stage and the aerodynamic optimization in the later vehicle stage. The optimization process is based on Hyperstudy software to realize the shape parameterization, and CFD software simulation is used to evaluate the aerodynamic performance. An automatic process was built to realize the aerodynamic shape optimization of cab behind engine vehicles with these two kinds of software. Eight design variables that need to be considered (i.e. sunshield rotation, hood deformation, container deformation, fairing optimization, front wheel baffle optimization, side deflector optimization, side skirt at the container, and rear guide device of the container) were determined for aerodynamic optimization design. Finally, the drag coefficient of the vehicle was reduced from 0.432 to 0.387, compared with that of the vehicle base model reduced 45 counts by 10.4%.

Key words: vehicle engineering, cab behind engine vehicles, aerodynamics, aerodynamic drag reduction, optimization design

CLC Number: 

  • U270.1

Fig.1

Simulation model"

Fig.2

Surface mesh"

Fig.3

Schematic diagram of mesh encryption area"

Table 1

Grid sensitivity check result"

A/mmB/mmC/mm网格数量/万Cd值
326412830010.4327
32649630520.4325
32489631810.4322
24489634200.4321
24486435120.4320
24326440170.4320
16326447620.4319

Fig.4

Schematic diagram of optimization process"

Fig.5

Deformation diagram of sunshield"

Table 2

Sunshield optimization results"

旋转角度α/（°）CdΔCd/%
00.4320
-20.428-0.86
-40.428-0.97
-60.427-1.25
-80.427-1.16
-100.426-1.30
-120.426-1.44
-140.425-1.64
-160.426-1.34
-180.428-1.00

Fig.5

Pressure distribution of Y= 0 before and after optimization"

Fig.7

Deformation diagram"

Fig.8

RBF fitting results"

Fig.9

Pressure distribution before and after optimization"

Table 3

Statistical table of optimization results"

参 数计算结果ΔCd/%
Base Cd0.432-
预测Cd0.420-2.78
变量M1.4-
变量N0-
实际计算Cd0.422-2.31
预测误差/%0.46-

Fig.10

Deformation diagram"

Table 4

Container optimization results"

方 案下压距离M/mCdΔCd/countsΔCd/%
10.150.4254-6.60-1.53
20.200.4224-9.60-2.22
30.250.4205-11.5-2.66
40.300.4198-12.2-2.82

Fig.11

Velocity vector of Y=0 section before and after optimization"

Fig.12

Optimization diagram of fairing"

Table 5

Optimization results of fairing"

方 案

X方向

平移/m

Y方向

平移/m

CdΔCd/counts
10.100.0800.4313-0.7
20.090.0720.43250.5
30.080.0640.4313-0.7
40.070.0560.4298-2.2
50.060.0480.4302-1.8
60.050.0400.4306-1.4
70.040.0320.4305-1.5
80.030.0240.4308-1.2

Fig.13

Pressure distribution before and after optimization"

Fig.14

Pressure distribution before and after optimization"

Fig.15

RBF fitting results"

Table 6

Statistical table of optimization results"

参 数差 值ΔCd/%
Base Cd0.42800.926
预测Cd0.4236-1.94
变量H/mm126.7-
变量β/（°）17.4°-
实际计算Cd0.4241-1.83
预测误差0.12-

Fig.16

Pressure distribution before and after optimization"

Fig.17

Side deflector"

Fig.18

RBF fitting results"

Table 7

Statistical table of optimization results"

参 数差 值ΔCd/%
Base Cd0.4320
优化导流板预测Cd0.4226-2.17
变量L/mm0.93-
变量β/（°）6.82-
实际计算Cd0.4249-1.64
预测误差/%0.54-

Fig.19

Turbulent kinetic energy of Y=0 cross section before and after optimization"

Fig.20

Diagrammatic sketch of container tail deformation"

Table 8

Optimization results of container tail"

X向移动距离/mCd值ΔCd/countsΔCd/%
0.20.4267-5.3-1.23
0.40.4256-6.4-1.48
0.60.4254-6.6-1.53
0.80.4253-6.7-1.55
1.00.4245-7.5-1.74
1.20.4239-8.1-1.88
1.40.4231-8.9-2.08
1.60.4265-5.5-1.27
1.80.459527.56.37
2.00.446614.63.38

Fig.21

Velocity vector diagram of Y=0 cross section before and after optimization"

Fig.22

Comparison of cumulated force coefficients of final scheme"

Fig.23

Front view comparison of front pressure distribution before and after optimization"

Fig.24

Side view comparison of front pressure distribution before and after optimization"

1 傅立敏. 汽车空气动力学[M]. 北京:机械工业出版社, 2006.
2 傅立敏. 用空气动力学附加装置降低国产货车气动阻力措施的探讨[J]. 汽车工程, 1994(3):144-148.
Fu Li-min. An investigation to the effects of add-on devices on reducing aerodynamic drag of domestic trucks[J]. Automotive Engineering, 1994(3):144-148.
3 Gong X, Gu Z, Li Z, et al. Aerodynamic shape optimization of a container-truck's wind deflector using approximate model[C]∥ SAE Paper, 2010-01-2035.
4 许亮. 重型卡车非光滑车身气动减阻特性研究[D]. 长沙:湖南大学机械与运载工程学院, 2014.
Xu Liang. Research on non-smooth body aerodynamic drag reduction characteristics of heavy trucks[D]. Changsha: College of Mechanical and Vehicle Engineering, Hunan University, 2014.
5 张凯歌. 重型卡车气动性能优化与实验研究[D]. 长沙:湖南大学机械与运载工程学院,2016.
Zhang Kai-ge. The aerodynamic perfomance optimization and experiment study of heavy duty truck[D]. Changsha: College of Mechanical and Vehicle Engineering, Hunan University,2016.
6 Cooper K R. Truck aerodynamics reborn - lessons from the past[C]∥ SAE Paper,2003-01-3376.
7 Englar R J. Development of pneumatic aerodynamic devices to improve the performance, economics, and safety of heavy vehicles[C]∥SAE Paper, 2000-01-2208.
8 Englar R J. Advanced aerodynamic devices to improve the performance, economics, handling, and safety of heavy vehicles[C]∥SAE Paper, 2001-01-2072.
9 Englar R J. Improved pneumatic aerodynamics for drag reduction, fuel economy, safety and stability increase for heavy vehicles[C]∥SAE Paper, 2005-01-3627.
10 Salati L, Cheli F, Schito P. Heavy truck drag reduction obtained from devices installed on the trailer[C]∥SAE Paper,2015-01-2898.
11 Woodiga S, Salazar D M, Wewengkang P, et al. Skin-friction topology on tail plate for tractor—trailer truck drag reduction[J]. Journal of Visualization, 2018,21(6):1017-1029.
12 金希东. 遗传算法及其应用[D]. 成都:西南交通大学电气工程学院, 1996.
Jin Xi-dong. Genetic algorithm and its application[D]. Chengdu: School of Electrical Engineering,Southwest Jiaotong University, 1996.
13 Deb K, Pratap A, Agarwal S, et al. A fast and elitist multi-objective genetic algorithm: NSGA-II[J]. IEEE Transactions on Evolutionary Computation, 2002, 6(2):182-197.
14 Kleijnen J P C. Simulation Optimization[M]. New York: Elsevier, 2015:101-138.
[1] Jie LI,Tao CHEN,Wen-cui GUO,Qi ZHAO. Pseudo excitation method of vehicle non-stationary random vibration in space domain and its application [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(4): 738-744.
[2] Li-jie ZHANG,Xi-ta A,Xiao TIAN,Wen LI. Multi⁃objective optimization design of accelerated degradation test based on Gamma process [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(2): 361-367.
[3] Wei-min ZHUANG,Shen CHEN,Nan WANG. Influence on thermal stress of autobody steel-aluminum clinch-adhesive connection structure [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(1): 70-78.
[4] Liang DUAN,Chun-yuan SONG,Chao LIU,Wei WEI,Cheng-ji LYU. State recognition in bearing temperature of high-speed train based on machine learning algorithms [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(1): 53-62.
[5] Xing-jun HU,Jing-long ZHANG,Yu-fei LUO,Li XIN,Sheng LI,Jin-rui HU,Wei LAN. Influence investigation of cooling tube structure and airflow direction on thermal⁃hydraulic performance of air⁃cooled charge air cooler [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(6): 1933-1942.
[6] Jian-bin CHEN,Song-ze ZHOU,Feng-yong FEI,Yong-long CHEN,Guo-ping LING. Influences of interference fit and knurling connection type on press fitting failure of assembled camshaft [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(6): 1959-1966.
[7] Yong LUO,Yong-heng WEI,Huan HUANG,Ren-jie XIAO,Lin REN,Huan-yu CUI. Starting control of P2.5 plug⁃in hybrid configuration dual⁃clutch based on driver's intention recognition [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(5): 1575-1582.
[8] Xiao-hua ZENG,Mei-jie SONG,Da-feng SONG,Yue WANG. Data processing method of bus driving cycle based on vehicular network information [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(5): 1692-1699.
[9] Chao MA,Yun-kai GAO,Zhe LIU,Yue-xing DUAN,Lin-li TIAN. Optimization of multi⁃material and beam cross⁃sectional shape and dimension of skeleton⁃type body [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(5): 1583-1592.
[10] Feng-chong LAN,Ji-wen LI,Ji-qing CHEN. DG-SLAM algorithm for dynamic scene compound deep learning and parallel computing [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(4): 1437-1446.
[11] Jian YANG,Qi XIA,Hai-chao ZHOU,Guo-lin WANG. Noise reduction mechanism of truck radial tire based on modified carcass string contour design [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(4): 1198-1203.
[12] Jiang-qi LONG,Jin-tao XIANG,Ping YU,Jun-cheng WANG. Linear disturbance observer suitable for sliding mode control of nonlinear active suspension [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(4): 1230-1240.
[13] Xin CHEN,Gui-shen YU,Biao ZHANG,Kai-xuan PAN,Li-fei YANG. Equivalent modeling of tensile-shear behavior for friction stir spot welding joints [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(4): 1190-1197.
[14] Wei LI,Huai-liang ZHANG,Wei QU. Design method of hydraulic straight pipe under random vibration [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(4): 1222-1229.
[15] Da-feng SONG,Li-li YANG,Xiao-hua ZENG,Xing-qi WANG,Wei-zhi LIANG,Nan-nan YANG. Battery life optimization of hybrid electric vehicle based on driving cycle construction [J]. Journal of Jilin University(Engineering and Technology Edition), 2021, 51(3): 781-791.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
Copyright © Journal of Jilin University(Engineering and Technology Edition), All Rights Reserved.
Tel: +86-431-85095297　Fax: +86-431-85094074　E-mail: xbgxb@jlu.edu.cn
Powered by Beijing Magtech Co. Ltd