吉林大学学报(工学版)

• • 上一篇    下一篇

高精度压电步进直线驱动器

赵宏伟,吴博达,程光明,刘国嵩,刘建芳,杨志刚   

  1. 吉林大学 机械科学与工程学院, 长春 130022
  • 收稿日期:2005-06-17 修回日期:2005-09-20 出版日期:2006-05-01 发布日期:2006-05-01
  • 通讯作者: 赵宏伟

Ultraprecision piezoelectric stepping linear actuator

Zhao Hong-wei, Wu Bo-da, Cheng Guang-ming, Liu Guo-song, Liu Jian-fang, Yang Zhi-gang   

  1. College of Mechanical Science and Engineering, Jilin University, Changchun 130022, China
  • Received:2005-06-17 Revised:2005-09-20 Online:2006-05-01 Published:2006-05-01
  • Contact: Zhao Hongwei

摘要: 提出一种以压电叠堆为驱动动力源的新型精密直线驱动器方案。定子采用柔性铰链双侧对钳方式交替对动子起到钳位作用。对驱动器工作原理进行了分析研究,建立了机械系统的数学模型。采用MSC Patran/Nastran软件对机械结构进行了仿真分析,并对所开发的驱动器样机进行了实验测试。测试结果与理论分析结果基本相符,样机的运动速度可达1.52 mm/min、单步最小位移(运动分辨率)为3.35 nm。驱动器性能稳定可靠,可望在精密工程等相关领域得到应用。

关键词: 机械工程, 直线驱动, 压电叠堆, 有限元仿真, 柔性铰链

Abstract: A new type of precise linear actuator using the piezoelectric stack as actuating element was presented. The stator clamps the rotor by a flexure hinge clamping structures in symmetrical directions. The working principle of the actuator was analyzed, and a mathematic model of the mechanical system was set up. The mechanical structure was simulated by the MSC Patran/Nastran software. The experimental test of the actuator prototype was performed and the test results were in agreement with the theoretical analysis results basically. The actuator prototype can move with speed 1.52 mm/min, and the minimum step size (moving resolution) is 3.35 nm. The actuator works stably and reliably, may be used in the domain of precision engineering.

Key words: mechanical engineering, linear actuation, piezoelectric stack, FEM simulation, flexure hinge

中图分类号: 

  • TN384
[1] 董伟,宋佰达,邱立涛,孙昊天,孙平,蒲超杰. 直喷汽油机暖机过程中两次喷射比例对燃烧和排放的影响[J]. 吉林大学学报(工学版), 2018, 48(6): 1755-1761.
[2] 贾拓,赵丁选,崔玉鑫. 铰接式装载机倾翻预警方法[J]. 吉林大学学报(工学版), 2018, 48(6): 1762-1769.
[3] 林学东, 江涛, 许涛, 李德刚, 郭亮. 高压共轨柴油机起动工况高压泵控制策略[J]. 吉林大学学报(工学版), 2018, 48(5): 1436-1443.
[4] 臧鹏飞, 王哲, 孙晨乐, 林炼炼. 直线增程器稳态运行换气过程[J]. 吉林大学学报(工学版), 2018, 48(5): 1455-1465.
[5] 李志军, 汪昊, 何丽, 曹丽娟, 张玉池, 赵新顺. 催化型微粒捕集器碳烟分布及其影响因素[J]. 吉林大学学报(工学版), 2018, 48(5): 1466-1474.
[6] 秦静, 徐鹤, 裴毅强, 左子农, 卢莉莉. 初始温度和初始压力对甲烷-甲醇裂解气预混层流燃烧特性的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1475-1482.
[7] 宫洵, 蒋冰晶, 胡云峰, 曲婷, 陈虹. 柴油机主-从双微元Urea-SCR系统非线性状态观测器设计与分析[J]. 吉林大学学报(工学版), 2018, 48(4): 1055-1062.
[8] 钟兵, 洪伟, 金兆辉, 苏岩, 解方喜, 张富伟. 进气门早关液压可变气门机构运动特性[J]. 吉林大学学报(工学版), 2018, 48(3): 727-734.
[9] 席雷, 徐亮, 高建民, 赵振, 王明森. 厚壁矩形带肋通道内蒸汽流动及传热特性[J]. 吉林大学学报(工学版), 2018, 48(3): 752-759.
[10] 许秀军, 李震, 王立权, 张同喜. 海流边界下初始铺管作业建模及半物理仿真[J]. 吉林大学学报(工学版), 2018, 48(3): 803-811.
[11] 李因武, 吴庆文, 常志勇, 杨成. 基于仿生斗齿的反铲液压挖掘机动臂仿真优化设计[J]. 吉林大学学报(工学版), 2018, 48(3): 821-827.
[12] 李龙, 张幽彤, 左正兴. 变负载控制在自由活塞内燃发电机的缸压控制中的应用[J]. 吉林大学学报(工学版), 2018, 48(2): 473-479.
[13] 刘汉光, 王国强, 孟东阁, 赵寰宇. 液压挖掘机履带行走装置的合理预张紧力[J]. 吉林大学学报(工学版), 2018, 48(2): 486-491.
[14] 田径, 刘忠长, 刘金山, 董春晓, 钟铭, 杜文畅. 基于燃烧边界参数响应曲面设计的柴油机性能优化[J]. 吉林大学学报(工学版), 2018, 48(1): 159-165.
[15] 卫海桥, 裴自刚, 冯登全, 潘家营, 潘明章. 压电喷油器多次喷射对GDI汽油机颗粒物排放的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 166-173.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!