吉林大学学报(工学版) ›› 2018, Vol. 48 ›› Issue (3): 835-844.doi: 10.13229/j.cnki.jdxbgxb20170189

• Orginal Article • Previous Articles     Next Articles

Erosion damage and evaluation of remanufacturing cladding layer for impeller metals FV520B

LIU Zi-wu1,2, LI Jian-feng1,2   

  1. 1.School of Mechanical Engineering, Shandong University, Jinan 250061, China;
    2.National Demonstration Center for Experimental Mechanical Engineering Education, Shandong University, Jinan 250061,China
  • Received:2017-03-05 Online:2018-05-20 Published:2018-05-20

RICH HTML

0   

PDF (PC)

307

Abstract: Coating layer with the same composition as the FV520B steel was deposited on the base material by laser cladding and Tungsten Inert Gas (TIG) cladding. Then, TIG cladding was tempered at 470 °C and 615 °C, respectively. The microstructure, hardness, erosion resistance of the cladding layers were investigated, and the surface quality, micro-hardness and residual stress were also tested after erosion. The results show that laser cladding with compact and symmetrical microstructure has the highest hardness, and TIG cladding with tempering has similar microstructure compared with the base material. With the increase in hardness, the erosion peak will move towards the high angle. When the impacting angle is less than 30°, the anti-erosion performance and surface quality of the laser cladding are better. At higher impacting angle, anti-erosion performance the laser cladding is worse than that of TIG cladding layer. For all the layers, erosion hardness is the lowest at the impacting angle with highest erosion rate, and erosion hardness is highest at the impacting angle of 90°. Both residual extend stress and residual compressive stress, which are caused by erosion, are maximal for laser cladding layer with highest hardness.

Key words: materials synthesis and processing technology, erosion evaluation of cladding layer, microstructural, surface roughness, erosion hardening, residual stress

CLC Number: 

  • TB31
[1] Utamura M,Fukuda T,Aritomii M.Aerodynamic characteristics of a centrifugal compressor working in supercritical carbon dioxide[J].Energy Procedia,2012,14:1149-1155.
[2] 舒林森,曹华军,许磊,等. 离心压缩机再制造叶轮结构特征三维建模方法及应用[J].机械工程学报,2014,50(3):184-190.
Shu Lin-sen,Cao Hua-jun,Xu Lei,et al.3D characteristic modeling method and application for remanufactured impeller of centrifugal compressor[J]. Journal of Mechanical Engineering,2014,50(3):184-190.
[3] Nakhaei R, Khodabandeh A, Najafi H.Effect of active gas on weld shape and microstructure of advanced A-TIG-Welded stainless steel[J]. Acta Metallurgica Sinica,2016,29(3):295-300.
[4] 徐滨士,刘世参,史佩京. 再制造工程和表面工程对循环经济贡献分析[J]. 中国表面工程,2006,19(1):1-6.
Xu Bin-shi,Liu Shi-can,Shi Pei-jing.Contribution of remanufacturing engineering and surface engineering to cycle economy[J].China Surface Engineering,2006,19(1):1-6.
[5] 周圣丰,戴晓琴,郑海忠. 激光熔覆与激光-感应复合熔覆WC-Ni60A 涂层的结构与性能特征[J]. 机械工程学报,2012,48(7):113-118.
Zhou Sheng-feng,Dai Xiao-qin,Zheng Hai-zhong.Characteristics on structure and properties of WC-Ni60A coatings by laser cladding and laser-induction hybrid clading[J]. Journal of Mechanical Engineering,2012,48(7):113-118.
[6] Rottwinkel B, Nölke C,Kaierle S,et al.Crack repair of single crystal turbine blades using laser cladding technology[J]. Procedia Cirp,2014,22(1):263-267.
[7] Xu Lei,Cao Hua-jun,Liu Hai-long,et al.Study on laser cladding remanufacturing process with FeCrNiCu alloy powder for thin-wall impeller blade[J]. The International Journal of Advanced Manufacturing Technology,2017,90(5-8):1383-1392.
[8] 黄薇. 激光熔覆技术在空压机叶轮修复上的应用[J]. 化工机械,2011,38(3):355-356.
Huang Wei.Laser cladding for repairing air compressor impellers[J]. Chemical Engineering & Machinery,2011,38(3):355-356.
[9] 姚建华,叶钟,沈红卫. 激光加工技术在汽轮机叶片制造中的应用[J]. 激光与光电子学进展,2012,49(3):104-109.
Yao Jian-hua,Ye Zhong,Shen Hong-wei.Application of laser processing technologies on turbine blades[J]. Laser & Optoelectronics Progress,2012,49(3):104-109.
[10] Wei Z,Yao J H,Dong C H,et al.Repairing and strengthening of eroded turbine blades by laser technology[J]. Journal of Power Engineering,2008,28(6):967-971.
[11] 余冬梅. 激光熔覆Stellite6/TiCN复合涂层的组织及性能研究[D]. 兰州:兰州理工大学材料学院,2014.
Yu Dong-mei.Investigation on microstructure and properties of Stellite6/TiCNcomposite coating by laser cladding[D]. Lanzhou: College of Materials, Lanzhou University of Technology,2014.
[12] 王璐,胡树兵,单炜涛,等. 激光熔覆NiCrMn-WC复合涂层的组织与耐磨性[J]. 中国有色金属学报,2014(1):145-151.
Wang Lu,Hu Shu-bing,Shan Wei-tao,et al. Microstructure and wear resistance of laser cladding NiCrMn-WC composite coatings[J]. The Chinese Journal of Nonferrous Metals, 2014(1):145-151.
[13] 李剑峰,王光存,刘子武,等. 一种气流喷砂式冲蚀磨损试验机[P]. 中国:CN103760048A,2014-04-30.
[14] 余永宁. 金属学原理[M].北京:冶金工业出版社,2013:422-423.
[15] 王光存. 离心压缩机叶轮冲蚀磨损机理和规律的研究[D]. 济南:山东大学机械工程学院, 2015.
Wang Guang-cun.Study on erosion wear mechanism and law of impeller in centrifugal compressor[D]. Jinan:School of Mechanical Engineering, Shandong University,2015.
[16] 张明. 离心压缩机叶轮材料FV520B超高周疲劳行为与机理研究[D]. 济南:山东大学机械工程学院,2015.
Zhang Ming.Research on fatigue behavior and mechanism of FV520B in very high cycle regime[D]. Jinan:School of Mechanical Engineering, Shandong University,2015.
[17] Agrawal S,Joshi S S.Analytical modelling of residual stresses in orthogonal machining of AISI4340 steel[J]. Journal of Manufacturing Processes,2013,15(1):56-68.
[18] Byrne G D,O’NeillL,Twomey B,et al. Comparison between shot peening and abrasive blasting processes as deposition methods for hydroxyapatite coatings onto a titanium alloy[J]. Surface and Coatings Technology,2013,216:224-231.
[1] JIANG Qiu-yue,YANG Hai-feng,TAN Cai-wang. Strengthening properties of welded joints of 22MnB5 super high strength steel [J]. Journal of Jilin University(Engineering and Technology Edition), 2018, 48(6): 1806-1810.
[2] ZHAO Shuang,SHEN Ji-hong,ZHANG Liu,ZHAO Han,CHEN Ke-fan. Evaluation of surface roughness of micro electrical discharge machining based-on fast Gauss algorithm [J]. Journal of Jilin University(Engineering and Technology Edition), 2018, 48(6): 1838-1843.
[3] HU Zhi-qing, YAN Ting-xu, LI Hong-jie, LYU Zhen-hua, LIAO Wei, LIU Geng. Effect of cryogenic treatment on punch-shearing performance of aluminum alloy sheet [J]. Journal of Jilin University(Engineering and Technology Edition), 2018, 48(5): 1524-1530.
[4] QIU Xiao-ming, WANG Yin-xue, YAO Han-wei, FANG Xue-qing, XING Fei. Multi-objective optimization of resistance spot welding parameters for DP1180/DP590 using grey relational analysis based Taguchi [J]. 吉林大学学报(工学版), 2018, 48(4): 1147-1152.
[5] CHEN Jun-fu, GUAN Zhi-ping, YANG Chang-hai, NIU Xiao-ling, JIANG Zhen-tao, Song Yu-quan. Comparison of strain ranges and mechanical properties of metal rods under tension and torsion tests [J]. 吉林大学学报(工学版), 2018, 48(4): 1153-1160.
[6] LIANG Xiao-bo, CAI Zhong-yi, GAO Peng-fei. Numerical simulation and experiment of cylindrical forming of sandwich composite panel [J]. 吉林大学学报(工学版), 2018, 48(3): 828-834.
[7] LIU Chun-guo, LIU Wei-dong, DENG Yu-shan. Effect of multi-point punch active loading path on the stretch-forming of sheet [J]. 吉林大学学报(工学版), 2018, 48(1): 221-228.
[8] LYU Meng-meng, GU Zheng-wei, XU Hong, LI Xin. Process optimization of hot stamping for anti-collision beam with ultra high strength [J]. 吉林大学学报(工学版), 2017, 47(6): 1834-1841.
[9] XING Hai-yan, GE Hua, LI Si-qi, YANG Wen-guang, SUN Xiao-jun. Hidden defect metal magnetic memory identification for welded joints based on fuzzy membership and maximum likelihood estimation [J]. 吉林大学学报(工学版), 2017, 47(6): 1854-1860.
[10] GU Xiao-yan, LIU Ya-jun, SUN Da-qian, XU Feng, MENG Ling-shan, GAO Shuai. Microstructures and mechanical properties of transient liquid phase diffusion bonded S355 steel/6005A aluminum alloy joint [J]. 吉林大学学报(工学版), 2017, 47(5): 1534-1541.
[11] GU Zheng-wei, ZHANG Wen-xue, LYU Meng-meng, WANG Wei, XU Hong, LI Xin. Stretch bending defect control of U-section stainless steel profile with wide flange [J]. 吉林大学学报(工学版), 2017, 47(4): 1165-1170.
[12] GU Zheng-wei, LYU Meng-meng, ZHANG Wen-xue, LEI Jiao-jiao, XU Hong. Stamping of front-end three-dimensional skin of China electric multiple units [J]. 吉林大学学报(工学版), 2017, 47(3): 869-875.
[13] YANG Xin-hui, XUE Wei, GUO Nan. Bending performance of glued-lumber beam reinforced with steel plate [J]. 吉林大学学报(工学版), 2017, 47(2): 468-477.
[14] LIANG Ji-cai, LI Yi, GAO Song, TENG Fei. Springback prediction for multi-point 3D stretch bending profile [J]. 吉林大学学报(工学版), 2017, 47(1): 185-190.
[15] XU Hong, LIU Ya-nan, YU Ting, GU Zheng-wei, LI Xiang-ji, ZHANG Zhi-qiang. Inelastic recovery behavior and microscopic mechanism of high strength DP780 steel during cyclic loading-unloading [J]. 吉林大学学报(工学版), 2017, 47(1): 191-198.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
[1] HE Lei,ZONG Chang-fu,TIAN Cheng-wei,WU Ren-jun,Zhang Tai-wu. DC motor fault diagnosis and fault tolerance control method for steer-by-wire car[J]. 吉林大学学报(工学版), 2011, 41(03): 608 -612 .
[2] LIU Song-shan, WANG Qing-nian, WANG Wei-hua, LIN Xin. Influence of inertial mass on damping and amplitude-frequency characteristic of regenerative suspension[J]. 吉林大学学报(工学版), 2013, 43(03): 557 -563 .
[3] CHU Liang, WANG Yan-bo, QI Fu-wei, ZHANG Yong-sheng. Control method of inlet valves for brake pressure fine regulation[J]. 吉林大学学报(工学版), 2013, 43(03): 564 -570 .
[4] LI Jing, WANG Zi-han, YU Chun-xian, HAN Zuo-yue, SUN Bo-hua. Design of control system to follow vehicle state with HIL test beach[J]. 吉林大学学报(工学版), 2013, 43(03): 577 -583 .
[5] HU Xing-jun, LI Teng-fei, WANG Jing-yu, YANG Bo, GUO Peng, LIAO Lei. Numerical simulation of the influence of rear-end panels on the wake flow field of a heavy-duty truck[J]. 吉林大学学报(工学版), 2013, 43(03): 595 -601 .
[6] WANG Tong-jian, CHEN Jin-shi, ZHAO Feng, ZHAO Qing-bo, LIU Xin-hui, YUAN Hua-shan. Mechanical-hydraulic co-simulation and experiment of full hydraulic steering systems[J]. 吉林大学学报(工学版), 2013, 43(03): 607 -612 .
[7] ZHANG Chun-qin, JIANG Gui-yan, WU Zheng-yan. Factors influencing motor vehicle travel departure time choice behavior[J]. 吉林大学学报(工学版), 2013, 43(03): 626 -632 .
[8] MA Wan-jing, XIE Han-zhou. Integrated control of main-signal and pre-signal on approach of intersection with double stop line[J]. 吉林大学学报(工学版), 2013, 43(03): 633 -639 .
[9] YU De-xin, TONG Qian, YANG Zhao-sheng, GAO Peng. Forecast model of emergency traffic evacuation time under major disaster[J]. 吉林大学学报(工学版), 2013, 43(03): 654 -658 .
[10] XIAO Yun, LEI Jun-qing, ZHANG Kun, LI Zhong-san. Fatigue stiffness degradation of prestressed concrete beam under multilevel amplitude cycle loading[J]. 吉林大学学报(工学版), 2013, 43(03): 665 -670 .
Copyright © Journal of Jilin University(Engineering and Technology Edition), All Rights Reserved.
Tel: +86-431-85095297　Fax: +86-431-85094074　E-mail: xbgxb@jlu.edu.cn
Powered by Beijing Magtech Co. Ltd