吉林大学学报(工学版) ›› 2016, Vol. 46 ›› Issue (2): 500-504.doi: 10.13229/j.cnki.jdxbgxb201602025

• 论文 • 上一篇    下一篇

应力状态对模具分区冷却热成形S-rail硬度分布的影响

胡平1, 2, 张金女1, 申国哲1, 林发财1, 刘立忠1   

  1. 1.大连理工大学 汽车工程学院,辽宁 大连 116024;
    2.大连理工大学 工业装备结构分析国家重点实验室,辽宁 大连 116024
  • 收稿日期:2014-07-12 出版日期:2016-02-20 发布日期:2016-02-20
  • 通讯作者: 申国哲(1973-),男,副教授,硕士生导师.研究方向:高强度钢板热冲压工艺与数值模拟技术.E-mail:sgz@dlut.edu.cn E-mail:pinghu@dlut.edu.cn
  • 作者简介:胡平(1956-),男,教授,博士生导师.研究方向:车辆数字化设计制造.E-mail:pinghu@dlut.edu.cn
  • 基金资助:
    "973"国家重大基础研究发展计划项目(2010CB832700); 中央高校基本科研业务费专项项目(DUT11ZD202); 高等学校博士学科点专项科研基金项目(20100041120017)

Influence of stress state on the hardness distribution of S-rail in tailored die quenching process

HU Ping1, 2, ZHANG Jin-nyu1, SHEN Guo-zhe1, LIN Fa-cai1, LIU Li-zhong1   

  1. 1.School of Automotive Engineering, Dalian University of Technology, Dalian 116024, China;
    2.State Key Laboratory of Structural Analysis for Industrial Equipment, Dalian University of Technology, Dalian 116024, China
  • Received:2014-07-12 Online:2016-02-20 Published:2016-02-20

RICH HTML

0   

PDF (PC)

380

摘要： 利用S-rail模具,以汽车用超高强度钢BR22MnB5为研究对象,结合模具分区冷却热成形工艺研究了模具温度及成形件应力状态对其最终硬度的影响.研究显示:随着模具温度升高,成形件的硬度减小;当模具热区和冷区的温度分别为400 ℃和室温(20 ℃)时,相应区域的硬度分别为300 HV和460 HV,热,冷区之间的硬度出现明显的梯度变化;板料在热成形过程中发生变形,其内圆角处受压应力,抑制马氏体生成,而外圆角处受拉应力,马氏体更易生成,所以外圆角硬度值大于其内圆角硬度值.

关键词: 材料合成与加工工艺, BR22MnB5, 模具分区冷却热成形, 应力状态, 硬度

Abstract: The influences of tool temperature and stress state of stamped part on its hardness distribution are investigated in tailed die quenching process of vehicle-use ultra high strength steel BR22MnB5. The results show that the hardness of the stamped part decreases with the increase in tool temperature. When the tool is heated up to 400 °C, a part with hardness of 300 HV in the hot region and 460 HV in the cold region is produced. Furthermore, during the stamping, the inner fillet of the stamped part is compressed while the outer fillet of the blank experiences tensile stress. So the hardness of the outer fillet is higher than that of the inner fillet in the stamped part.

Key words: materials synthesis and processing technology, BR22MnB5, tailored die quenching, stress sate, hardness

中图分类号: 

  • TG306
[1] Altan T. Hot-stamping boron-alloyed steels for automotive parts[J].Stamping Journal, 2006, 12: 40-43.
[2] Svec T, Grüner M, Merklein M. FE-Simulation of the heat transfer by defined cooling conditions during the hot stamping process[J]. Key Engineering Materials, 2011, 473:699-706.
[3] 马宁, 申国哲, 张宗华, 等. 高强度钢板热冲压材料性能研究及在车身设计中的应用[J].机械工程学报, 2011, 47(8): 60-65.
Ma Ning, Shen Guo-zhe, Zhang Zong-hua, et al. Material performance of hot-forming high strength steel and its application in vehicle body[J]. Journal of Mechanical Engineering, 2011, 47(8): 60-65.
[4] 姜大鑫.高强度钢板热成形多场耦合关系研究[D]. 大连:大连理工大学汽车工程学院, 2012.
Jiang Da-xin. Research on high strength steel multi-filed coupled relationships in hot forming[D]. Dalian: School of Vehicle Engineering, Dalian University of Technology, 2012.
[5] Merklein M, Svec T. Hot stamping: manufacturing functional optimized components[J]. Production Engineering, 2013,7(2/3):141-151.
[6] Bardelcik A, Salisbury C P, Winkler S, et al. Effect of cooling rate on the high strain rate properties of boron steel[J]. International Journal of Impact Engineering, 2010,37 (6):694-702.
[7] George R, Bardelcik A, Worswick M J. Hot forming of boron steels using heated and cooled tooling for tailored properties[J].Journal of Materials Processing Technology, 2012, 212(11) : 2386-2399.
[8] 盈亮,戴明华,胡平,等. 高强度热成形钢板冷却速率-强度-硬度预测[J]. 吉林大学学报:工学版,2014, 44(6): 1716-1722.
Ying Liang, Dai Ming-hua, Hu Ping, et al. Strength and hardness prediction based on cooling rate for hot forming high strength steel[J]. Journal of Jilin University (Engineering and Technology Edition), 2014, 44(6): 1716-1722.
[9] Banik J, Lenze F J, Sikora S, et al. Tailored properties-a pivotal question for hot forming[C]//Proceedings of the 3th International Conference on Hot Sheet Metal Forming of High-Performance Steel, Kassel, Germany, 2011:13-20.
[10] Svec T, Merklein M. Tailored tempering-heat transfer and resulting properties in dependency of tool temperatures[C]//Proceedings of the 3th International Conference on Hot Sheet Metal Forming of High-Performance Steel, Kassel, Germany, 2011:21-29.
[11] Feuser P, Schweiker T, Merklein M. Partially hot-formed parts from 22MnB5-process window material characteristics and component test results[C]//The 10th International Conference on Technology of Plasticity, Aachen, Germany, 2011: 408-413.
[12] Lee S W, Yoon J W, Yang D Y. Comparative investigation into the dynamic explicit and the static implicit method for spring back of sheet metal stamping[J]. Engineering Computations, 1999, 16(2/3):347-373.
[13] Patel J R, Cohen M. Criterion for the action of applied stress in the martensitic transformation[J]. Acta Metallurgica, 1953, 1(5):531-538.
[14] Olson G B, Cohen M. Stress-assisted isothermal martensitic-transformation-application to TRIP steels[J]. Metallurgical Transactions A-physical Metallurgy and Materials Science, 1982, 13(11): 1907-1914.
[15] 贾治域. 车用高强钢热成形过程热-力-相变实验研究[D].大连:大连理工大学汽车工程学院,2013.
Jia Zhi-yu. Experimental research on thermal-mechanical-phase transformation of vehicle high strength steel hot forming process[D].Dalian: School of Vehicle Engineering, Dalian University of Technology, 2013.
[1] 那景新,慕文龙,范以撒,谭伟,杨佳宙. 车身钢-铝粘接接头湿热老化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1653-1660.
[2] 姜秋月,杨海峰,檀财旺. 22MnB5超高强钢焊接接头强化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1806-1810.
[3] 胡志清, 颜庭旭, 李洪杰, 吕振华, 廖伟, 刘庚. 深冷处理对铝合金薄板冲剪成形性能的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1524-1530.
[4] 邱小明, 王银雪, 姚汉伟, 房雪晴, 邢飞. 基于灰色关联的DP1180/DP590异质点焊接头工艺参数优化[J]. 吉林大学学报(工学版), 2018, 48(4): 1147-1152.
[5] 陈俊甫, 管志平, 杨昌海, 牛晓玲, 姜振涛, 宋玉泉. 金属棒试样拉伸和扭转试验应变范围和力学特性对比[J]. 吉林大学学报(工学版), 2018, 48(4): 1153-1160.
[6] 关庆丰, 董书恒, 郑欢欢, 李晨, 张从林, 吕鹏. 强流脉冲电子束作用下45#钢表面Cr合金化[J]. 吉林大学学报(工学版), 2018, 48(4): 1161-1168.
[7] 梁晓波, 蔡中义, 高鹏飞. 夹芯复合板柱面成形的数值模拟及试验[J]. 吉林大学学报(工学版), 2018, 48(3): 828-834.
[8] 刘子武, 李剑峰. 叶片材料FV520B再制造熔覆层冲蚀损伤行为及评价[J]. 吉林大学学报(工学版), 2018, 48(3): 835-844.
[9] 刘纯国, 刘伟东, 邓玉山. 多点冲头主动加载路径对薄板拉形的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 221-228.
[10] 张志强, 刘从豪, 何东野, 李湘吉, 李纪萱. 基于性能梯度分布的硼钢热冲压工艺对形状精度的影响[J]. 吉林大学学报(工学版), 2017, 47(6): 1829-1833.
[11] 吕萌萌, 谷诤巍, 徐虹, 李欣. 超高强度防撞梁热冲压成形工艺优化[J]. 吉林大学学报(工学版), 2017, 47(6): 1834-1841.
[12] 王辉, 周杰, 熊煜, 陶亚平, 向荣. 基于逆向工程的复杂曲面冲压件回弹补偿[J]. 吉林大学学报(工学版), 2017, 47(6): 1842-1847.
[13] 王春生, 邹丽, 杨鑫华. 基于邻域粗糙集的铝合金焊接接头疲劳寿命影响因素分析[J]. 吉林大学学报(工学版), 2017, 47(6): 1848-1853.
[14] 邢海燕, 葛桦, 李思岐, 杨文光, 孙晓军. 基于模糊隶属度最大似然估计的焊缝隐性缺陷磁记忆信号识别[J]. 吉林大学学报(工学版), 2017, 47(6): 1854-1860.
[15] 谷晓燕, 刘亚俊, 孙大千, 徐锋, 孟令山, 高帅. S355钢/6005A铝合金瞬间液相扩散连接接头组织与性能[J]. 吉林大学学报(工学版), 2017, 47(5): 1534-1541.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 《吉林大学学报(工学版)》编辑部
地址：长春市人民大街5988号　电话：+86-431-85095297　传真：+86-431-85094074　E-mail: xbgxb@jlu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发