吉林大学学报(工学版) ›› 2016, Vol. 46 ›› Issue (5): 1478-1483.doi: 10.13229/j.cnki.jdxbgxb201605015

• • 上一篇    下一篇

应用推迟点火、废气再循环及过稀混合气降低稀燃甲醇发动机NOx排放

李小平, 洪伟, 解方喜, 李翔宇, 杨文海, 代志尧   

  1. 吉林大学 汽车仿真与控制国家重点实验室, 长春 130022
  • 收稿日期:2015-07-02 出版日期:2016-09-20 发布日期:2016-09-20
  • 通讯作者: 解方喜(1982-),男,副教授,博士.研究方向:内燃机工作过程优化与控制.E-mail:jluxfx@126.com
  • 作者简介:李小平(1984-),男,工程师,博士研究生.研究方向:内燃机公害与排放控制.E-mail:lixp2008@jlu.edu.cn
  • 基金资助:
    国家自然科学基金项目(51206059); 吉林省青年科研基金项目(20140520128JH).

NOx emission reduction of a lean-burn methanol engine by retarding ignition timing, exhaust gas recirculation and leaner air/fuel mixture

LI Xiao-ping, HONG Wei, XIE Fang-xi, LI Xiang-yu, YANG Wen-hai, DAI Zhi-yao   

  1. State Key Laboratory of Automotive Simulation and Control,Jilin University, Changchun 130022,China
  • Received:2015-07-02 Online:2016-09-20 Published:2016-09-20

摘要: 为降低稀燃时NOx排放及改善燃油消耗率-NOx排放“(be-NOx)”折中关系,以一台基于柴油机改制的进气道喷射点燃式甲醇发动机为试验对象,在1400 r/min、4.52 kg/h甲醇消耗量工况条件,以及1.5过量空气系数和21 °CA BTDC点火提前角的基础上,研究了推迟点火、废气再循环(EGR)及过稀混合气3种策略对稀燃甲醇发动机燃烧和NOx排放的影响。结果表明:3种策略均能在机内有效净化NOx排放,实现接近零排放的效果。在相同NOx排放水平下,与过稀混合气策略相比,EGR策略的燃烧滞后和延长程度有所减弱,循环变动降低,而推迟点火策略的燃烧更为滞后,但燃烧持续期和循环变动减小。对比而言,EGR策略能获得更佳的“be-NOx”折中关系;推迟点火策略的“be-NOx”折中性能虽较EGR策略有所降低,但排气温度有所升高,有利于提高样机在低负荷时后处理器的转化效率,从减小排放角度具有一定应用潜力。

关键词: 动力机械工程, 稀燃甲醇发动机, 推迟点火, 废气再循环, 过稀混合气, NOx排放

Abstract: To reduce NOx emission and improve the trade-off relationship between fuel consumption ratio (be) and NOx under lean-burn operation, the influences of three strategies: retarding ignition timing, Exhaust Gas Recirculation (EGR) and leaner air/fuel mixture on the engine combustion performance and NOx emission were experimentally investigated at light load on a port-injection and spark ignition methanol engine, which was modified from a diesel engine. In the experiments the engine speed, fuel consumption, air excess coefficient and ignition advance angle were fixed at 1400 r/min, 4.53 kg/h, 1.5 m and 210 °CA BTDC respectively. Results show that all three strategies can achieve the effect of NOx purification inside the cylinder, and the NOx emission approach zero. At the same level of NOx emission, compared with the air/fuel mixture strategy, the combustion delaying and extension of the EGR strategy are weakened, and the coefficient of cyclic variation is decreased. The combustion of the retarding ignition timing strategy is more delayed than the leaner air/fuel mixture strategy, but the duration of combustion and the coefficient of cyclic variation are decreased. In contrast, the EGR strategy can get better be-NOx trade-off than retarding ignition timing; however, the rise of the exhaust temperature by retarding ignition timing is helpful to improve the conversion efficiency of the catalytic converter at light load. Therefore, retarding ignition timing has the application potential to reduce emissions.

Key words: power machinery and engineering, lean-burn methanol engine, retarding ignition timing, exhaust gas recirculation, leaner air/fuel mixtures, NOx emission

中图分类号: 

  • TK46
[1] Wheeler J, Stein J, Hunter G. Effects of charge motion, compression ratio, and dilution on a medium duty natural gas single cylinder research engine[C]∥SAE Paper, 2014-01-2363.
[2] Tang Qi-jun, Liu Jing-ping, Zhan Zhang-song,et al. Influences on combustion characteristics and performances of EGR vs. lean burn in a gasoline engine[C]∥SAE Paper, 2013-01-1125.
[3] Vancoillie J, Demuynck J, Sileghem L,et al. The potential of methanol as a fuel for flex-fuel and dedicated spark-ignition engines[J]. Applied Energy,2013,102:140-149.
[4] Zhang Bo, Ji Chang-wei, Wang Shuo-feng. Combustion analysis and emissions characteristics of a hydrogen-blended methanol engine at various spark timings[J]. International Journal of Hydrogen Energy, 2015,40(13):4707-4716.
[5] Gukelberger R, Alger T, Mangold B, et al. Effects of EGR dilution and fuels on spark plug temperatures in gasoline engines[C]∥SAE Paper, 2013-01-1632.
[6] Alger T, Mangold B, Robets C, et al. The interaction of fuel anti-knock index and cooled EGR on engine performance and efficiency[C]∥SAE Paper, 2012-01-1149.
[7] Li Jun, Gong Chang-ming, Su Yan, et al. Effect of injection and ignition timings on performance and emissions from a spark-ignition engine fueled with methanol[J].Fuels,2010,89(12):3919-3925.
[8] Schöffler T, Hoffmann K. Stoichiometric natural gas combustion in a single cylinder SI engine and impact of charge dilution by means of EGR[C]∥SAE Paper,2013-24-0113.
[9] Blank H, Dismon H, Kochs M W, et al. EGR and air management for direct injection gasoline engines[C]∥SAE Paper,2002-01-0707.
[1] 董伟,宋佰达,邱立涛,孙昊天,孙平,蒲超杰. 直喷汽油机暖机过程中两次喷射比例对燃烧和排放的影响[J]. 吉林大学学报(工学版), 2018, 48(6): 1755-1761.
[2] 林学东, 江涛, 许涛, 李德刚, 郭亮. 高压共轨柴油机起动工况高压泵控制策略[J]. 吉林大学学报(工学版), 2018, 48(5): 1436-1443.
[3] 李志军, 汪昊, 何丽, 曹丽娟, 张玉池, 赵新顺. 催化型微粒捕集器碳烟分布及其影响因素[J]. 吉林大学学报(工学版), 2018, 48(5): 1466-1474.
[4] 秦静, 徐鹤, 裴毅强, 左子农, 卢莉莉. 初始温度和初始压力对甲烷-甲醇裂解气预混层流燃烧特性的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1475-1482.
[5] 宫洵, 蒋冰晶, 胡云峰, 曲婷, 陈虹. 柴油机主-从双微元Urea-SCR系统非线性状态观测器设计与分析[J]. 吉林大学学报(工学版), 2018, 48(4): 1055-1062.
[6] 钟兵, 洪伟, 金兆辉, 苏岩, 解方喜, 张富伟. 进气门早关液压可变气门机构运动特性[J]. 吉林大学学报(工学版), 2018, 48(3): 727-734.
[7] 席雷, 徐亮, 高建民, 赵振, 王明森. 厚壁矩形带肋通道内蒸汽流动及传热特性[J]. 吉林大学学报(工学版), 2018, 48(3): 752-759.
[8] 李龙, 张幽彤, 左正兴. 变负载控制在自由活塞内燃发电机的缸压控制中的应用[J]. 吉林大学学报(工学版), 2018, 48(2): 473-479.
[9] 田径, 刘忠长, 刘金山, 董春晓, 钟铭, 杜文畅. 基于燃烧边界参数响应曲面设计的柴油机性能优化[J]. 吉林大学学报(工学版), 2018, 48(1): 159-165.
[10] 卫海桥, 裴自刚, 冯登全, 潘家营, 潘明章. 压电喷油器多次喷射对GDI汽油机颗粒物排放的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 166-173.
[11] 李志军, 何丽, 姜瑞, 申博玺, 孔祥金, 刘世宇. 柴油机微粒捕集器灰分分布对其压降的影响评价[J]. 吉林大学学报(工学版), 2017, 47(6): 1760-1766.
[12] 郭亮, 杨文昭, 王云开, 孙万臣, 程鹏, 李国良. 废气再循环对丁醇/柴油混合燃料发动机的影响[J]. 吉林大学学报(工学版), 2017, 47(6): 1767-1774.
[13] 虞浏, 刘忠长, 刘江唯, 杜宏飞, 许允. 直喷汽油机喷雾粒径特性[J]. 吉林大学学报(工学版), 2017, 47(5): 1482-1488.
[14] 刘忠长, 腾鹏坤, 田径, 许允, 亓升林, 于凯波. 二级增压柴油机旁通阀调节特性[J]. 吉林大学学报(工学版), 2017, 47(3): 796-803.
[15] 彭玮, 李国祥, 闫伟. 适用于发动机散热器的壁面函数改进[J]. 吉林大学学报(工学版), 2017, 47(3): 804-810.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 刘松山, 王庆年, 王伟华, 林鑫. 惯性质量对馈能悬架阻尼特性和幅频特性的影响[J]. 吉林大学学报(工学版), 2013, 43(03): 557 -563 .
[2] 初亮, 王彦波, 祁富伟, 张永生. 用于制动压力精确控制的进液阀控制方法[J]. 吉林大学学报(工学版), 2013, 43(03): 564 -570 .
[3] 李静, 王子涵, 余春贤, 韩佐悦, 孙博华. 硬件在环试验台整车状态跟随控制系统设计[J]. 吉林大学学报(工学版), 2013, 43(03): 577 -583 .
[4] 朱剑峰, 林逸, 陈潇凯, 施国标. 汽车变速箱壳体结构拓扑优化设计[J]. 吉林大学学报(工学版), 2013, 43(03): 584 -589 .
[5] 胡兴军, 李腾飞, 王靖宇, 杨博, 郭鹏, 廖磊. 尾板对重型载货汽车尾部流场的影响[J]. 吉林大学学报(工学版), 2013, 43(03): 595 -601 .
[6] 王同建, 陈晋市, 赵锋, 赵庆波, 刘昕晖, 袁华山. 全液压转向系统机液联合仿真及试验[J]. 吉林大学学报(工学版), 2013, 43(03): 607 -612 .
[7] 张春勤, 姜桂艳, 吴正言. 机动车出行者出发时间选择的影响因素[J]. 吉林大学学报(工学版), 2013, 43(03): 626 -632 .
[8] 马万经, 谢涵洲. 双停车线进口道主、预信号配时协调控制模型[J]. 吉林大学学报(工学版), 2013, 43(03): 633 -639 .
[9] 于德新, 仝倩, 杨兆升, 高鹏. 重大灾害条件下应急交通疏散时间预测模型[J]. 吉林大学学报(工学版), 2013, 43(03): 654 -658 .
[10] 肖赟, 雷俊卿, 张坤, 李忠三. 多级变幅疲劳荷载下预应力混凝土梁刚度退化[J]. 吉林大学学报(工学版), 2013, 43(03): 665 -670 .