液压挖掘机履带行走装置的合理预张紧力

doi:10.13229/j.cnki.jdxbgxb20161245

吉林大学学报(工学版) ›› 2018, Vol. 48 ›› Issue (2): 486-491.doi: 10.13229/j.cnki.jdxbgxb20161245

液压挖掘机履带行走装置的合理预张紧力

刘汉光^{1, 2}, 王国强³, 孟东阁¹, 赵寰宇³

1.江苏徐州工程机械研究院,江苏徐州 221004;
2.徐工集团高端工程机械智能制造国家重点实验室,江苏徐州 221004;
3.吉林大学机械科学与工程学院,长春 130022

收稿日期:2016-11-18 出版日期:2018-03-01 发布日期:2018-03-01
作者简介:刘汉光(1971-),男,高级工程师.研究方向:整机可靠性设计.E-mail:liuhangguang2@xcmg.com
基金资助:
国家重点研发计划项目(2016YFC0802910); 国家科技支撑计划项目(2015BAF07B02)

Reasonable pre-tension research of crawler traveling gear of hydraulic excavator

LIU Han-guang^{1, 2}, WANG Guo-qiang³, MENG Dong-ge¹, ZHAO Huan-yu³

1.Jiangsu Xuzhou Construction Machinery Research Institute, Xuzhou 221004, China;
2.Jiangsu Xuzhou State Key Laboratory of Intelligent Manufacturing of Advanced Construction Machinery, Xuzhou 221004, China;
3.College of Mechanical Science and Engineering, Jilin University, Changchun 130022, China

Received:2016-11-18 Online:2018-03-01 Published:2018-03-01

摘要/Abstract

摘要： 针对液压挖掘机履带行走装置的合理预张紧力进行了分析研究。在多体动力学软件RecurDyn中建立了挖掘机的虚拟样机模型,并通过实验测得了在直行、原地转向以及差速转向3种工况下的履带行走装置张紧力的曲线,与仿真结果进行对比,验证了虚拟样机模型的准确。通过对直行、爬坡以及原地转向3种典型工况下的仿真分析,得到了在改变履带行走装置预张紧力情况下,履带行驶时张紧力的变化情况,通过张紧力曲线的标准差来判断其波动情况,进而得到合理的预张紧力与车重的比例系数。

关键词: 机械工程, 液压挖掘机, 虚拟样机仿真, 预张紧力

Abstract: The research focuses on the determination of reasonable pre-tension of crawler traveling gear of hydraulic excavator. The virtual prototype model of the excavator was established in the multi-body dynamics software RecurDyn. The pre-tension curves of the crawler traveling gear were obtained by experiments under three working conditions, horizontal straight, pivot steering and differential steering. Experiment results verified the accuracy of the virtual prototype model by comparing with the simulation results. By simulation analysis of three typical working conditions, horizontal straight, climbing, and pivot steering, the changes of the track tension during movement on wheel were obtained with the transformations of pre-tension of the crawler driving device. According to the judgment of the fluctuations based on the standard deviation of the tension curves, the reasonable proportional coefficient between the pre-tension and vehicle weight is received.

Key words: mechanical engineering, hydraulic excavator, virtual prototype model simulation, pre-tension

中图分类号:

U469

刘汉光, 王国强, 孟东阁, 赵寰宇. 液压挖掘机履带行走装置的合理预张紧力[J]. 吉林大学学报(工学版), 2018, 48(2): 486-491.

LIU Han-guang, WANG Guo-qiang, MENG Dong-ge, ZHAO Huan-yu. Reasonable pre-tension research of crawler traveling gear of hydraulic excavator[J]. 吉林大学学报(工学版), 2018, 48(2): 486-491.

参考文献

[1] Nakanishi T,Shabana A A. Contact forces in the non-linear dynamic analysis of tracked vehicles [J]. International Journal for Numerical Methods in Engineering, 1994, 37(8):1251-1275.
[2] Nakanishi T,Shabana A A. On the numerical solution of tracked vehicle dynamic equations [J]. Nonlinear Dynamics, 1994, 6(6):391-417.
[3] Choi J H, Lee H C, ShabanaH A A. Spatial dynamics of multi-body tracked vehicles part I: spatial equations of motion [J]. Vehicle System Dynamics, 1998, 29(1):27-49.
[4] Lee H C, Choi J H, ShabanaH A A. Spatial dynamics of multi-body tracked vehicles part II: contact forces and simulation results [J]. Vehicle System Dynamics, 1998, 29(2):113-137.
[5] Huh K, Hong D. Tracktension estimation in tracked vehicles under various maneuvering tasks [J]. Journal of Dynamic Systems Measurement & Control, 2001, 123(2):179-185.
[6] Matej J. Terrain-adaptive auxiliary track tensioning system for tracked vehicles [J]. Journal of Computational & Nonlinear Dynamics, 2013, 8(3):689-698.
[7] Zhou M X, Ren Y P, Ye L, et al. Discussion oftrack tension for heavy tracked vehicles [J]. Advanced Materials Research, 2013, 813:30-33.

相关文章 15

[1]	董伟,宋佰达,邱立涛,孙昊天,孙平,蒲超杰. 直喷汽油机暖机过程中两次喷射比例对燃烧和排放的影响[J]. 吉林大学学报(工学版), 2018, 48(6): 1755-1761.
[2]	贾拓,赵丁选,崔玉鑫. 铰接式装载机倾翻预警方法[J]. 吉林大学学报(工学版), 2018, 48(6): 1762-1769.
[3]	林学东, 江涛, 许涛, 李德刚, 郭亮. 高压共轨柴油机起动工况高压泵控制策略[J]. 吉林大学学报(工学版), 2018, 48(5): 1436-1443.
[4]	臧鹏飞, 王哲, 孙晨乐, 林炼炼. 直线增程器稳态运行换气过程[J]. 吉林大学学报(工学版), 2018, 48(5): 1455-1465.
[5]	李志军, 汪昊, 何丽, 曹丽娟, 张玉池, 赵新顺. 催化型微粒捕集器碳烟分布及其影响因素[J]. 吉林大学学报(工学版), 2018, 48(5): 1466-1474.
[6]	秦静, 徐鹤, 裴毅强, 左子农, 卢莉莉. 初始温度和初始压力对甲烷-甲醇裂解气预混层流燃烧特性的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1475-1482.
[7]	宫洵, 蒋冰晶, 胡云峰, 曲婷, 陈虹. 柴油机主-从双微元Urea-SCR系统非线性状态观测器设计与分析[J]. 吉林大学学报(工学版), 2018, 48(4): 1055-1062.
[8]	钟兵, 洪伟, 金兆辉, 苏岩, 解方喜, 张富伟. 进气门早关液压可变气门机构运动特性[J]. 吉林大学学报(工学版), 2018, 48(3): 727-734.
[9]	席雷, 徐亮, 高建民, 赵振, 王明森. 厚壁矩形带肋通道内蒸汽流动及传热特性[J]. 吉林大学学报(工学版), 2018, 48(3): 752-759.
[10]	许秀军, 李震, 王立权, 张同喜. 海流边界下初始铺管作业建模及半物理仿真[J]. 吉林大学学报(工学版), 2018, 48(3): 803-811.
[11]	李因武, 吴庆文, 常志勇, 杨成. 基于仿生斗齿的反铲液压挖掘机动臂仿真优化设计[J]. 吉林大学学报(工学版), 2018, 48(3): 821-827.
[12]	李龙, 张幽彤, 左正兴. 变负载控制在自由活塞内燃发电机的缸压控制中的应用[J]. 吉林大学学报(工学版), 2018, 48(2): 473-479.
[13]	田径, 刘忠长, 刘金山, 董春晓, 钟铭, 杜文畅. 基于燃烧边界参数响应曲面设计的柴油机性能优化[J]. 吉林大学学报(工学版), 2018, 48(1): 159-165.
[14]	卫海桥, 裴自刚, 冯登全, 潘家营, 潘明章. 压电喷油器多次喷射对GDI汽油机颗粒物排放的影响[J]. 吉林大学学报(工学版), 2018, 48(1): 166-173.
[15]	李志军, 何丽, 姜瑞, 申博玺, 孔祥金, 刘世宇. 柴油机微粒捕集器灰分分布对其压降的影响评价[J]. 吉林大学学报(工学版), 2017, 47(6): 1760-1766.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed

液压挖掘机履带行走装置的合理预张紧力

Reasonable pre-tension research of crawler traveling gear of hydraulic excavator

RICH HTML

PDF (PC)

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

Metrics

本文评价

推荐阅读 10