吉林大学学报(工学版) ›› 2022, Vol. 52 ›› Issue (11): 2542-2548.doi: 10.13229/j.cnki.jdxbgxb20210333

• 材料科学与工程 • 上一篇    

超声冲击对搅拌摩擦焊缝疲劳性能的影响

王磊1(),黄秉汉2,丛家慧2,3,回丽3,周松2,3,徐永臻2   

  1. 1.苏州科技大学 机械工程学院，江苏 苏州 215000
    2.沈阳航空航天大学 机电工程学院，沈阳 110136
    3.沈阳航空航天大学 航空制造工艺数字化国防重点学科实验室，沈阳 110136
  • 收稿日期:2021-03-12 出版日期:2022-11-01 发布日期:2022-11-16
  • 作者简介:王磊（1981-），男，教授，博士. 研究方向：航空材料及焊接结构强度评定，损伤修复与寿命分析.E-mail： leiwang@sau.edu.cn
  • 基金资助:
    国家自然科学基金项目(51775355);辽宁省百千万人才资助项目(2020-78-B46)

Effect of ultrasonic impact on fatigue performance of friction stir weld

Lei WANG1(),Bing-han HUANG2,Jia-hui CONG2,3,Li HUI3,Song ZHOU2,3,Yong-zhen XU2   

  1. 1.College of Mechanical Engineering，Suzhou University of Science and Technology，Suzhou 215000，China
    2.School of Mechatronics Egineering，Shenyang Aerospace University，Shenyang 110136，China
    3.Key Laboratory of Fundamental Science for National Defense of Aeronautical Digital Manufacturing Process，Shenyang Aerospace University，Shenyang 110136，China
  • Received:2021-03-12 Online:2022-11-01 Published:2022-11-16

RICH HTML

 3   

PDF (PC)

183

摘要：

采用超声冲击对铝合金2024-T4搅拌摩擦焊焊缝进行处理，对冲击前后试样进行残余应力、微观组织、显微硬度和疲劳性能的对比分析。结果表明：超声冲击处理之后，试样的表面引入残余压应力，平均残余压应力可达263 MPa；试样经过超声冲击处理表层组织得到细化，变形层深度可达50~70 μm，表面硬度由175 HV提升到235 HV；超声冲击处理的试样疲劳寿命明显提高，超声冲击试样是未冲击试样疲劳寿命的1.72~2倍，疲劳裂纹萌生的位置由表面转移至强化层以下的亚表面。

关键词: 机械工程, 铝合金, 搅拌摩擦焊, 超声冲击, 疲劳性能

Abstract:

Ultrasonic impact is used to process the welding seam of aluminum alloy 2024-T4 friction stir welding. The residual stress， microstructure， microhardness and fatigue performance of the specimens before and after ultrasonic impact were compared and analyzed. The results show， after ultrasonic impact treatment， residual compressive stress is introduced into the surface of the specimen， and the average residual compressive stress can reach 263 MPa. The surface structure of the sample is refined after ultrasonic impact treatment， the depth of the deformation layer can reach 50~70 μm， and the surface hardness is increased from 175 HV to 235 HV. The fatigue life of the specimens treated by ultrasonic impact are significantly improved. The fatigue life of the ultrasonic impact specimens are 1.72~2 times that of the unimpacted specimens， and the location of fatigue crack initiation is transferred from the surface to the subsurface below the strengthening layer.

Key words: mechanical engineering, aluminum alloy, friction stir welding, ultrasonic impact, fatigue performance

中图分类号: 

  • TG405

表1

2024铝合金的化学成分"

元素质量分数/%
Si0.5
Fe0.5
Cu3.8~4.9
Mg1.2~1.8
Zn0.3
Ti0.15
Mn0.3~0.9
其他Ni：0.1， Fe+Ni：0.5
Al余量

图1

疲劳试样示意图"

图2

试样截面硬度测试示意图"

图3

超声冲击处理试样沿深度硬度测试示意图"

图4

表面残余应力分布图"

图5

超声冲击改变材料表层结构示意图"

图6

超声冲击后试样显微组织"

图7

超声冲击处理前、后硬度对比"

图8

超声冲击处理试样沿深度方向硬度测试"

图9

超声冲击处理前、后焊接接头疲劳寿命"

图10

未处理试样疲劳断口"

图11

超声冲击试样疲劳断口"

1 徐滨士,朱绍华. 表面工程的理论与技术[M]. 北京: 国防工业出版社, 1999.
2 张文博, 徐开国, 张汝春. 焊接接头疲劳强度的研究及其技术工艺的改进[J]. 煤矿机械, 2005(3):70-73.
Zhang Wen-bo, Xu Kai-guo, Zhang Ru-chun. Research on fatigue strength of welded joints and improvement of technical process[J]. Coal Mining Machinery, 2005(3): 70-73.
3 王炳英,霍立兴,王东坡,等.等离子喷涂法改善焊接结构的疲劳性能[J].焊接学报,2006,27(12): 97-100.
Wang Bing-ying, Huo Li-xing, Wang Dong-po, et al. Plasma spraying method improves the fatigue performance of welded structures[J]. Transactions of the China Welding Institution, 2006, 27(12): 97-100.
4 Gao Y K, Wu X R. Experimental investigation and fatigue life prediction for 7475-T7351 aluminum alloy with and without shot peening-induced residual stresses[J]. Acta Materialia, 2011, 59(9): 3737-3747.
5 He B L, Wei K, Yu Y X, et al. Fatigue life analysis of SMA490BW steel welded but joint for train bogie based on ABAQUS/FE-SAFE[J]. China Welding, 2016(4): 5-12.
6 王桂阳,王海斗,张玉波,等.超声冲击法提高焊接接头疲劳特性研究进展[J]. 材料导报, 2016, 30(9): 87-94.
Wang Gui-yang, Wang Hai-dou, Zhang Yu-bo, et al. Research progress on improving fatigue characteristics of welded joints by ultrasonic impact method[J]. Materials Guide, 2016, 30(9): 87-94.
7 鲁金忠, 季仕杰, 吴刘军, 等. 激光冲击⁃超声滚压复合工艺对AZ91D镁合金力学性能的影响[J]. 吉林大学学报: 工学版, 2020, 50(4): 1301-1309.
Lu Jin-zhong, Ji Shi-jie, Wu Liu-jun, et al. Effect of laser shock ultrasonic rolling composite process on mechanical properties of AZ91D magnesium alloy[J]. Journal of Jilin University(Engineering and Technology Edition), 2020,50(4): 1301-1309.
8 白易立, 王东坡, 邓彩艳, 等. 超声冲击强度对焊接接头疲劳寿命的影响[J]. 焊接学报, 2019, 40(12): 149-153, 168.
Bai Yi-li, Wang Dong-po, Deng Cai-yan, et al. Influence of ultrasonic impact strength on fatigue life of welded joints[J]. Transactions of the China Welding Institution, 2019, 40(12): 149-153, 168.
9 Poja S, Farshid Z, Mohammad A, et al. Experimental study of transverse attachment joints with 40 and 60 mm thick main plates, improved by high-frequency mechanical impact treatment(HFMI)-science direct[J]. Engineering Structures, 2018, 155: 251-266.
10 Almohaisen A M N, Hassan K S. Improving the mechanical properties of aluminum alloys 6061-T6 friction stir welding joints using ultrasonic peening[J]. IOP Conference Series: Materials Science and Engineering, 2020, 881(1): 012093.
11 吴圣川, 胡雅楠, 康国政. 材料疲劳损伤行为的先进光源表征技术[M]. 北京: 科学出版社, 2018.
12 Askeland Donald R, Phule Pradeep P. Essentials of Materials Science and Engineering[M]. Beijing: Defence Industry Press, 2004.
13 Ruslan K, Young-Sik P, Erfan M, et al. An improvement in fatigue behavior of AISI 4340 steel by shot peening and ultrasonic nanocrystal surface modification[J]. Materials Science and Engineering, 2020, 791: 139752.
14 Zhang W W, Lawrence Y Y, Noyan I C. Microscale laser shock peening of thin films, part 1: experiment, modeling and s imulation[J]. Journal of Manufacturing Science and Engineering, 2004, 126(1): 10-17.
15 Tan Y, Wu G, Yang J M, et al. Laser shock peening on fatigue crack growth behavior of aluminum alloy[J]. Fatigue & Fracture of Engineering Materials & Structures, 2003, 27: 649-655.
[1] 朱凌,王秋成. 空间几何约束下新能源汽车驱动系统协调控制方法[J]. 吉林大学学报(工学版), 2022, 52(7): 1509-1514.
[2] 金兆辉,谷乐祺,洪伟,解方喜,尤田. 液压可变气门系统压力波动的影响分析[J]. 吉林大学学报(工学版), 2022, 52(4): 773-780.
[3] 张岩,刘玮,张树勇,裴毅强,董蒙蒙,秦静. 二/四冲程可变柴油机燃烧室热负荷的改善[J]. 吉林大学学报(工学版), 2022, 52(3): 504-514.
[4] 李国发,王彦博,何佳龙,王继利. 机电装备健康状态评估研究进展及发展趋势[J]. 吉林大学学报(工学版), 2022, 52(2): 267-279.
[5] 赵文伯,李玉洁,邓俊,李理光,吴志军. 针阀运动规律及其对喷嘴内流和喷雾特性影响[J]. 吉林大学学报(工学版), 2022, 52(10): 2234-2243.
[6] 胡兴军,张靖龙,辛俐,罗雨霏,王靖宇,余天明. 冷却管结构及风速对空冷中冷器性能的影响[J]. 吉林大学学报(工学版), 2021, 51(5): 1557-1564.
[7] 庄蔚敏,王鹏跃,高瑞娟,解东旋. 温热成形对AA5754铝合金静态力学性能的影响[J]. 吉林大学学报(工学版), 2021, 51(3): 847-854.
[8] 罗开玉,陈俊成,王长雨,鲁金忠. 光斑直径对激光冲击强化铝合金腐蚀性能的影响[J]. 吉林大学学报(工学版), 2021, 51(2): 501-510.
[9] 赵庆武,程勇,杨雪,王宁. 高重频纳秒脉冲放电点火系统设计[J]. 吉林大学学报(工学版), 2021, 51(2): 414-421.
[10] 翟富刚,尹燕斌,李超,田纬,乔子石. 伺服电动缸传动系统刚度建模与前馈控制[J]. 吉林大学学报(工学版), 2021, 51(2): 442-449.
[11] 李志军,刘浩,张立鹏,李振国,邵元凯,李智洋. 过滤壁结构对颗粒捕集器深床过滤影响的模拟[J]. 吉林大学学报(工学版), 2021, 51(2): 422-434.
[12] 梁继才,廖雁飞,滕菲,梁策,李义. 矩形截面型材三维多点拉弯成形减薄率[J]. 吉林大学学报(工学版), 2021, 51(1): 163-171.
[13] 王忠,李游,张美娟,刘帅,李瑞娜,赵怀北. 柴油机排气阶段颗粒碰撞过程动力学特征分析[J]. 吉林大学学报(工学版), 2021, 51(1): 39-48.
[14] 胡云峰,丁一桐,赵志欣,蒋冰晶,高金武. 柴油发动机燃烧过程数据驱动建模与滚动优化控制[J]. 吉林大学学报(工学版), 2021, 51(1): 49-62.
[15] 田银宝,申俊琦,胡绳荪,勾健. EP/EN模数对铝合金VP-CMT焊熔滴过渡及焊道成形的影响[J]. 吉林大学学报(工学版), 2020, 50(5): 1663-1668.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 《吉林大学学报(工学版)》编辑部
地址：长春市人民大街5988号　电话：+86-431-85095297　传真：+86-431-85094074　E-mail: xbgxb@jlu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发