Journal of Jilin University(Engineering and Technology Edition) ›› 2022, Vol. 52 ›› Issue (12): 2765-2777.doi: 10.13229/j.cnki.jdxbgxb20210401

    Next Articles

Start up control strategy of plug in hybrid system based on double clutch transmission

Yong LUO1,2(),Yi SUI3,Fu-tao SHEN2,Qiang SUN4,Yun-xiao DENG2,Yong-heng WEI2   

  1. 1.State Key Laboratory of Vehicle NVH and Safety Control，China Automotive Engineering Research Institute Co. ，Ltd. ，Chongqing 401122，China
    2.Key Laboratory of Advanced Manufacturing Technology for Automobile Parts，Chongqing University of Technology，Chongqing 400054，China
    3.College of Mechanical and Power Engineering，Chongqing University of Science and Technology，Chongqing 401331，China
    4.Technical Center，Ningbo Jiecheng Automobile Technology Co. ，Ltd. ，Ningbo 315048，China
  • Received:2021-05-06 Online:2022-12-01 Published:2022-12-08

RICH HTML

 27   

PDF (PC)

395

Abstract:

The coordinated control of multiple power sources and dual clutches in the starting process of dual clutch plug-in hybrid vehicle is studied. Firstly， the dynamics of different starting modes of the system is analyzed， and the system mathematical model and starting performance evaluation index are established. On this basis， considering SOC， load condition， slope and other factors and the driver's starting intention， the system starting mode decision-making method is established. The coordinated control strategy of power source and dual clutch for each starting mode is formulated with the maximum impact as the constraint. The simulation results show that the selection of starting mode under different working conditions is reasonable. The maximum impact degree is 7.31 m/s3， and the maximum sliding friction work is 4.94 kJ， all within a reasonable range， which verifies the effectiveness of the strategy.

Key words: vehicle engineering, plug-in hybrid electric vehicle, dual clutch transmission, start-up process control, road conditions, driver's intention

CLC Number: 

  • U463.2

Fig.1

Structure of P2.5-PHPS based on DCT"

Table 1

Working status of power source and clutch of different start-up types"

起步类型动力源双离合器
发动机电机C1C2
纯电动起步不工作工作不工作不工作
单离合器C1起步工作不工作工作不工作
单离合器C2起步工作不工作不工作工作
联合起步C1最终结合工作不工作工作工作
联合起步C2最终结合工作不工作工作工作

Fig.2

Simplified DCT system dynamics model based on P2.5 configuration"

Fig.3

P2.5-PHPS start-up mode selection strategy"

Fig.4

P2.5-PHPS start-up process control logic"

Fig.5

P2.5-PHPS start-up simulation model framework"

Fig.6

Engine torque characteristic model"

Fig.7

Efficiency model of P2.5 drive motor"

Table 2

Basic parameters of research objects"

参 数数值
整备质量/kg1580
轮胎半径/m0.308
滚动系数0.015
风阻系数0.31
迎风面积/m22.226
发动机峰值扭矩/（N·m）80
发动机峰值功率/kW45
P2.5电机峰值扭矩/（N·m）172
P2.5电机峰值功率/kW80
一/二挡到轮端速比（发动机）13.95/7.466
二挡到轮端速比（P2.5驱动电机）8.245

Fig.8

Driver's start-up intention recognitionverification"

Fig.9

Pure electric start-up simulation results"

Fig.10

Simulation results of engine combined with dual clutch start-up"

Fig.11

Simulation results of dual power joint start-up"

1 罗勇,韦永恒,黄欢,等. 驾驶员意图识别的P2.5插混构型双离合器起步控制[J]. 吉林大学学报:工学版,2021,51(5):1575-1582.
Luo Yong, Wei Yong-heng, Huang Huan, et al. Starting control of P2.5 plug⁃in hybrid configuration dual⁃clutch based on driver's intention recognition[J]. Journal of Jilin University(Engineering and Technology Edition), 2021,51(5): 1575-1582.
2 Yang Y, Zhang Y T, Tian J Y, et al. Adaptive real-time optimal energy management strategy for extender range electric vehicle[J]. Energy, 2020, 197: No.117237.
3 Hong J C, Wang Z P, Zhang T Z, et al. Research on integration simulation and balance control of a novel load isolated pure electric driving system[J]. Energy, 2019, 189: No.116220.
4 Kulkarni M, Shim T, Zhang Y. Shift dynamics and control of dual-clutch transmissions[J]. Mechanism and Machine Theory, 2007, 42(2): 168-182.
5 Goetz M, Levesley M C, Crolla D A. Dynamics and control of gearshifts on twin-clutch transmissions[J]. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 2005, 219(8): 951-963.
6 Bao R, Avila V, Baxter J. Effect of 48 V mild hybrid system layout on powertrain system efficiency and its potential of fuel economy improvement[C]∥SAE Tech-nical Paper, 2017-01-1175.
7 Xu X, Liang Y, Jordan M, et al. Optimized control of engine start assisted by the disconnect clutch in a P2 hybrid automatic transmission[J]. Mechanical Systems and Signal Processing, 2019, 124: 313-329.
8 Yang C, Song J, Li L, et al. Economical launching and accelerating control strategy for a single-shaft parallel hybrid electric bus[J]. Mechanical Systems and Signal Processing, 2016, 76: 649-664.
9 Tao G, Wu M, Meng F. Online performance evaluation of a heavy-duty automatic transmission launching process[J]. Mechatronics, 2016, 38: 143-150.
10 Wang X, Li L, Yang C. Hierarchical control of dry clutch for engine-start process in a parallel hybrid electric vehicle[J]. IEEE Transactions on Transportation Electrification, 2016, 2(2): 231-243.
11 Zhang Jin-le, Ma Biao, Zheng Chang-song, et al. Improved fuzzy control of dual clutch transmission during launch process[C]∥2010 IEEE International Conference on Mechatronics and Automation, Xi'an, China, 2010: 676-681.
12 Zhao Z G, Jiang J L, Yu Z P, et al. Start-up sliding mode variable structure that coordinates the control and real-time optimization of dry dual clutch transmissions[J]. International Journal of Automotive Technology, 2013, 14(6): 875-888.
13 Lu Xiao-hui, Gao Bing-zhao, Chen Hong. Q-learning based adaptive PID controller design for AMT clutch engagement during start-up process[C]∥Proceedings of the 31st Chinese Control Conference, Hefei, China, 2012: 3131-3136.
14 Zhao Z, Li X, He L, et al. Estimation of torques transmitted by twin-clutch of dry dual-clutch transmission during vehicle's launching process[J]. IEEE Transactions on Vehicular Technology, 2016, 66(6): 4727-4741.
15 Zhao Z G, Chen H J, Zhen Z X, et al. Optimal torque coordinating control of the launching with twin clutches simultaneously involved for dry dual-clutch transmission[J]. Vehicle System Dynamics, 2014, 52(6): 776-801.
16 张军. DCT传动系统参数化建模及仿真分析[D]. 合肥:合肥工业大学机械与汽车工程学院, 2012.
Zhang Jun. Parametric modeling and simulation analysis of the DCT transmission system[D]. Hefei:College of Mechanical and Automotive Engineering, Hefei University of Technology, 2012.
17 Galvagno E, Velardocchia M, Vigliani A. Dynamic and kinematic model of a dual clutch transmission[J]. Mechanism and Machine Theory, 2011, 46(6): 794-805.
18 王伟,王庆年,田涌君,等. 基于模糊控制功率分流式混合动力客车控制策略[J]. 吉林大学学报: 工学版,2017,47(2): 337-343.
Wang Wei, Wang Qing-nian, Tian Yong-jun, et al. Control strategy of power-split hybrid electric bus based on fuzzy control[J]. Journal of Jilin University (Engineering and Technology Edition), 2017, 47(2): 337-343.
19 Jiang G, Lin Y, Qin D, et al. Torque coordination control strategy in engine start-up process for a single motor hybrid electric vehicle[J]. International Journal of Electric and Hybrid Vehicles, 2018, 10(2):177-196.
20 Wu J, Zhang C H, Cui N X. Fuzzy energy management strategy for a hybrid electric vehicle based on driving cycle recognition[J]. International Journal of Automotive Technology, 2012, 13(7):1159-1167.
21 Zhang N, Zhao F, Luo Y, et al. A dynamic coordinated control strategy for the mode-switch of HEV based on motor speed closed-loop control[J]. Automotive Engineering, 2014, 36(2):134-138.
22 Su Y, Hu M, Su L, et al. Dynamic coordinated control during mode transition process for a plug-in hybrid electric vehicle[J]. IEEE Access, 2019(7):53891-53908.
[1] Deng-feng WANG,Hong-li CHEN,Jing-xin NA,Xin CHEN. Failure comparison of single and double lap joints after high temperature aging [J]. Journal of Jilin University(Engineering and Technology Edition), 2023, 53(2): 346-354.
[2] Pei ZHANG,Zhi-wei WANG,Chang-qing DU,Fu-wu YAN,Chi-hua LU. Oxygen excess ratio control method of proton exchange membrane fuel cell air system for vehicle [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 1996-2003.
[3] Ke-yong WANG,Da-tong BAO,Su ZHOU. Data-driven online adaptive diagnosis algorithm towards vehicle fuel cell fault diagnosis [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2107-2118.
[4] Qi-ming CAO,Hai-tao MIN,Wei-yi SUN,Yuan-bin YU,Jun-yu JIANG. Hydrothermal characteristics of proton exchange membrane fuel cell start⁃up at low temperature [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2139-2146.
[5] Hai-lin KUI,Ze-zhao WANG,Jia-zhen ZHANG,Yang LIU. Transmission ratio and energy management strategy of fuel cell vehicle based on AVL⁃Cruise [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2119-2129.
[6] Yan LIU,Tian-wei DING,Yu-peng WANG,Jing DU,Hong-hui ZHAO. Thermal management strategy of fuel cell engine based on adaptive control strategy [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2168-2174.
[7] Cheng LI,Hao JING,Guang-di HU,Xiao-dong LIU,Biao FENG. High⁃order sliding mode observer for proton exchange membrane fuel cell system [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2203-2212.
[8] Xun-cheng CHI,Zhong-jun HOU,Wei WEI,Zeng-gang XIA,Lin-lin ZHUANG,Rong GUO. Review of model⁃based anode gas concentration estimation techniques of proton exchange membrane fuel cell system [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 1957-1970.
[9] Yao-wang PEI,Feng-xiang CHEN,Zhe HU,Shuang ZHAI,Feng-lai PEI,Wei-dong ZHANG,Jie-ran JIAO. Temperature control of proton exchange membrane fuel cell thermal management system based on adaptive LQR control [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2014-2024.
[10] Guang-di HU,Hao JING,Cheng LI,Biao FENG,Xiao-dong LIU. Multi⁃objective sliding mode control based on high⁃order fuel cell model [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2182-2191.
[11] Feng-xiang CHEN,Qi WU,Yuan-song LI,Tian-de MO,Yu LI,Li-ping HUANG,Jian-hong SU,Wei-dong ZHANG. Matching，simulation and optimization for 2.5 ton fuel cell/battery hybrid forklift [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2044-2054.
[12] Xiao-hua WU,Zhong-wei YU,Zhang-ling ZHU,Xin-mei GAO. Fuzzy energy management strategy of fuel cell buses [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(9): 2077-2084.
[13] Qing GAO,Hao-dong WANG,Yu-bin LIU,Shi JIN,Yu CHEN. Experimental analysis on spray mode of power battery emergency cooling [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(8): 1733-1740.
[14] Kui-yang WANG,Ren HE. Recognition method of braking intention based on support vector machine [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(8): 1770-1776.
[15] Han-wu LIU,Yu-long LEI,Xiao-feng YIN,Yao FU,Xing-zhong LI. Multi⁃point control strategy optimization for auxiliary power unit of range⁃extended electric vehicle [J]. Journal of Jilin University(Engineering and Technology Edition), 2022, 52(8): 1741-1750.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
[1] TAN Mei, YIN Yi-long, YANG Wei-hui. Method at Region Level for Ridge Distance[J]. 吉林大学学报(工学版), 2005, 35(05): 537 -0541 .
[2] QIU Jian-xin,WANG Xi-ei,FAN Xiao-hun. Information Integration between Computer Aided Design System and[J]. 吉林大学学报(工学版), 2005, 35(05): 505 -0510 .
[3] LI Yong-qiang, ZHAO Xi-hua, ZHAO He, LI Min，ZHANG Wei-hua . Effect of preheating temperature on weld shaping and microstructure
for laser lap welding of aluminum alloy[J]. 吉林大学学报(工学版), 2008, 38(05): 1065 -1068 .
[4] AN Shi, LI Jing, CUI Na . Simulation of commuter day-to-day dynamic route switching behavior under ATIS information[J]. 吉林大学学报(工学版), 2009, 39(03): 587 -0592 .
[5] DUAN Bin, SUN Tong-jing,LI Zhen-hua, HUANG Chang-wei,ZHANG Guang-xian. IIR Butterworth digital filter for full digital inverter[J]. 吉林大学学报(工学版), 2009, 39(增刊2): 311 -0314 .
[6] JIN Jing-Fu, MA Yi, LIU Yu-Rong, CONG Qian. Aerodynamic analysis of the family of airfoil of owl[J]. 吉林大学学报(工学版), 2010, 40(增刊): 278 -0281 .
[7] YU Xiao-hui， SHI Yao-wu. Cross-spectral ESPRIT Method for LFM Parameter[J]. 吉林大学学报(工学版), 2005, 35(05): 551 -0555 .
[8] KONG Fan-sen,WANG Jun,SUN Hai-gang . Fuzzy comprehensive evaluation of equipment usability of engine cylinder block production line based on AHP[J]. 吉林大学学报(工学版), 2008, 38(06): 1332 -1336 .
[9] HE Dong-ye，YANG Shen-hua，KOU Shu-qing . Numerical analysis on fracture splitting technology of main bearing block of engine[J]. 吉林大学学报(工学版), 2009, 39(01): 78 -82 .
[10] SHI Wen-Xiao, GONG Jing. An uplink packet scheduling algorithm based on WiMAX[J]. 吉林大学学报(工学版), 2010, 40(05): 1386 -1391 .
Copyright © Journal of Jilin University(Engineering and Technology Edition), All Rights Reserved.
Tel: +86-431-85095297　Fax: +86-431-85094074　E-mail: xbgxb@jlu.edu.cn
Powered by Beijing Magtech Co. Ltd