吉林大学学报(工学版) ›› 2011, Vol. 41 ›› Issue (02): 327-0332.

• 论文 • 上一篇    下一篇

轮胎印迹压电式汽车轴距差检测误差补偿方法

张立斌1,苏建1,单洪颖2,田永军1,刘苏超1   

  1. 1.吉林大学 交通学院,长春130022;2.吉林大学 机械科学与工程学院,长春130022
  • 收稿日期:2009-12-14 出版日期:2011-03-01 发布日期:2011-03-01
  • 通讯作者: 单洪颖(1973-),女,副教授.研究方向:生产制造系统仿真.E-mail:shan-hy@jlu.edu.cn E-mail:shan-hy@jlu.edu.cn
  • 作者简介:张立斌(1971-),男,教授,博士生导师.研究方向:汽车检测与诊断.E-mail:zlb@jlu.edu.cn
  • 基金资助:

    国家自然科学基金项目(50775094)

Error compensation method of piezoelectric detection by tire print of vehicle wheelbase difference

ZHANG Li-bin1,SU Jian1,SHAN Hong-ying2,TIAN Yong-jun1,LIU Su-chao1   

  1. 1.College of Transportation, Jilin University, Changchun 130022,China;2.College of Mechanical Science and Engineering, Jilin University,Changchun 130022|China
  • Received:2009-12-14 Online:2011-03-01 Published:2011-03-01

摘要:

基于压电电缆传感器的工作特性,提出了轮胎印迹压电式汽车轴距差检测方法。设计了具有双梯型底槽结构的检测装置,针对该检测装置进行了轮胎印迹压电电压信号波形分析。基于相对测量理论建立了汽车直线行驶、斜直线行驶及曲线行驶情况下的轴距差检测数学模型,并进行了检测误差补偿方法分析。对轮胎印迹压电式轴距差检测方法进行了试验研究,结果表明,该装置可对车轮在检测台板上的横向位置进行精确测量,实现曲线行驶情况下的检测误差补偿。检测结果证明了本文建立的理论模型的正确性。该轴距差检测装置具有很高的检测精度,且可靠性高、成本低,具有很好的推广应用价值。

关键词: 车辆工程, 轮胎印迹, 压电电缆, 左右轴距差, 误差补偿

Abstract:

A method of piezoelectric detection by tire print of the vehicle wheelbase difference was proposed based on the working behavior of the piezoelectric cable sensor. A detection device with dual trapezoidal bottom slot was designed and its tire print piezoelectric voltage signal waveform was analyzed. Mathematical models of the wheelbase difference detection under the conditions of the vehicle driving in straight line, in oblique line and in curved line were built based on the relative measurement theory, and the detection error compensation method was analyzed. The proposed method was investigated by test , the result showed that the onboard traverse position of the wheel can be measured precisely by the developed device, the compensation of the detection error caused by curved driving can be realized. The detection results proved the correctness of the built theoretical model. The wheelbase difference detection device is characterized by high accuracy, high reliability and low cost, with good prospects for practical application.

Key words: vehicle engineering, tire print, piezoelectric cables, wheelbase difference, error compensation

中图分类号: 

  • U463
[1] 常成,宋传学,张雅歌,邵玉龙,周放. 双馈电机驱动电动汽车变频器容量最小化[J]. 吉林大学学报(工学版), 2018, 48(6): 1629-1635.
[2] 席利贺,张欣,孙传扬,王泽兴,姜涛. 增程式电动汽车自适应能量管理策略[J]. 吉林大学学报(工学版), 2018, 48(6): 1636-1644.
[3] 何仁,杨柳,胡东海. 冷藏运输车太阳能辅助供电制冷系统设计及分析[J]. 吉林大学学报(工学版), 2018, 48(6): 1645-1652.
[4] 那景新,慕文龙,范以撒,谭伟,杨佳宙. 车身钢-铝粘接接头湿热老化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1653-1660.
[5] 刘玉梅,刘丽,曹晓宁,熊明烨,庄娇娇. 转向架动态模拟试验台避撞模型的构建[J]. 吉林大学学报(工学版), 2018, 48(6): 1661-1668.
[6] 赵伟强, 高恪, 王文彬. 基于电液耦合转向系统的商用车防失稳控制[J]. 吉林大学学报(工学版), 2018, 48(5): 1305-1312.
[7] 宋大凤, 吴西涛, 曾小华, 杨南南, 李文远. 基于理论油耗模型的轻混重卡全生命周期成本分析[J]. 吉林大学学报(工学版), 2018, 48(5): 1313-1323.
[8] 朱剑峰, 张君媛, 陈潇凯, 洪光辉, 宋正超, 曹杰. 基于座椅拉拽安全性能的车身结构改进设计[J]. 吉林大学学报(工学版), 2018, 48(5): 1324-1330.
[9] 那景新, 浦磊鑫, 范以撒, 沈传亮. 湿热环境对Sikaflex-265铝合金粘接接头失效强度的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1331-1338.
[10] 王炎, 高青, 王国华, 张天时, 苑盟. 混流集成式电池组热管理温均特性增效仿真[J]. 吉林大学学报(工学版), 2018, 48(5): 1339-1348.
[11] 金立生, 谢宪毅, 高琳琳, 郭柏苍. 基于二次规划的分布式电动汽车稳定性控制[J]. 吉林大学学报(工学版), 2018, 48(5): 1349-1359.
[12] 隗海林, 包翠竹, 李洪雪, 李明达. 基于最小二乘支持向量机的怠速时间预测[J]. 吉林大学学报(工学版), 2018, 48(5): 1360-1365.
[13] 王德军, 魏薇郦, 鲍亚新. 考虑侧风干扰的电子稳定控制系统执行器故障诊断[J]. 吉林大学学报(工学版), 2018, 48(5): 1548-1555.
[14] 胡满江, 罗禹贡, 陈龙, 李克强. 基于纵向频响特性的整车质量估计[J]. 吉林大学学报(工学版), 2018, 48(4): 977-983.
[15] 刘国政, 史文库, 陈志勇. 考虑安装误差的准双曲面齿轮传动误差有限元分析[J]. 吉林大学学报(工学版), 2018, 48(4): 984-989.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
No Suggested Reading articles found!