吉林大学学报(工学版) ›› 2018, Vol. 48 ›› Issue (2): 507-517.doi: 10.13229/j.cnki.jdxbgxb20170953

• • 上一篇    下一篇

大豆籽粒形状和尺寸分析及其建模

王扬, 吕凤妍, 徐天月, 于建群   

  1. 吉林大学 生物与农业工程学院,长春 130022
  • 收稿日期:2017-02-05 出版日期:2018-03-01 发布日期:2018-03-01
  • 通讯作者: 于建群(1958-),男,教授,博士生导师. 研究方向:农业机械的数字化设计. E-mail:yujianqun@jlu.edu.cn
  • 作者简介:王扬(1987-),男,博士研究生. 研究方向:农业机械的数字化设计. E-mail:yangwl2@mails.jlu.edu.cn
  • 基金资助:
    国家自然科学基金项目(51675218)

Shape and size analysis of soybean kernel and modeling

WANG Yang, LYU Feng-yan, XU Tian-yue, YU Jian-qun   

  1. College of Biological and Agricultural Engineering, Jilin University, Changchun 130022, China
  • Received:2017-02-05 Online:2018-03-01 Published:2018-03-01

摘要: 为建立大豆籽粒的离散元法分析模型,对大豆籽粒的几何形状和尺寸参数进行了测试分析。由测试分析可知,大豆籽粒的几何形状与椭球近似,三轴尺寸均服从正态分布,三轴尺寸中主尺寸与次尺寸间存在一定的函数关系。在此基础上,提出一种基于球充填的大豆籽粒建模方法,即将大豆籽粒的几何形状简化成椭球形,以实际大豆籽粒的各三轴尺寸平均值作为椭球的三轴尺寸,采用球充填方法建立椭球(单个籽粒)的分析模型;选单个籽粒分析模型的主尺寸,按正态分布随机生成,次尺寸通过与主尺寸的关系计算得出,由此建立具有不同尺寸及分布的大豆籽粒群体模型。以2个品种大豆籽粒为例,通过堆积试验和本文提出的“自流筛分”试验的仿真与试验结果对比可知,当充填球数为5时,仿真结果与试验结果较接近,初步证明了本文提出的大豆籽粒建模方法的可行性和有效性。

关键词: 农业工程, 离散元法, 大豆籽粒, 颗粒建模, 仿真分析

Abstract: In order to build the analytic model of soybean kernel using Discrete Element Method (DEM), the shape and size of soybean kernel are measured and analyzed. It is found that the shape of a soybean kernel can be approximated to an ellipsoid. The three axis dimensions follow normal distribution, and there exists a certain correlation between the primary dimension and the secondary dimension. On this basis, a soybean kernel modeling method is proposed based on the sphere filling. The shape of the soybean kernel is approximated to an ellipsoid, and the three axis dimensions are determined as the mean values of measured soybean kernels. The primary dimension of the analytical model of a kernel, which follows normal distribution, is randomly generated, and the secondary dimension of the kernel is calculated according to the relationship between the primary and secondary dimensions. As a result, the assemble model of the soybean kernels with different size and distribution is built. Two varieties of soybean kernels are selected as the research objects. By comparison between the simulated results and the experimental results of the packing test and the self-flowing screening test proposed in this work, it is shown that, when the amount of filling-spheres is five, the simulation results are in good agreement with the experiment results, thus, preliminarily verifying the effectiveness and feasibility of proposed modeling method.

Key words: agricultural engineering, discrete element method, soybean kernel, particle modelling, simulation analysis

中图分类号: 

  • S126
[1] Cundall P A, Strack O L. A discrete numerical model for granular assemblies[J]. Géotechnique,1979,29(1):47-65.
[2] 于建群,付宏,李红,等. 离散元法及其在农业机械工作部件研究与设计中的应用[J]. 农业工程学报,2005,21(5):1-6.
Yu Jian-qun, Fu Hong, Li Hong, et al. Application of discrete element method to research and design of working parts of agricultural machines[J]. Transactions of the Chinese Society of Agricultural Engineering,2005,21(5):1-6.
[3] Vu-Quoc L, Zhang X, Walton O R. A 3-D discrete-element method for dry granular flows of ellipsoidal particles[J]. Computer Methods in Applied Mechanics and Engineering,2000,187:483-528.
[4] Boac J M, Casada M E, Maghirang R G, et al. Material and interaction properties of selected grains and oilseeds for modeling discrete particles[J]. Transactions of the ASABE,2010,53(4):1201-1216.
[5] Tao H, Zhong W, Jin B. Comparison of construction method for DEM smulation of ellipsoidal particles[J]. Chinese Journal of Chemical Engineering,2013,21(7):800-807.
[6] Li Z Q, Yu J Q, Feng Z R, et al. Simulation and performance analysis of a soybean seed metering device using discrete element method[J]. Sensor Letters,2013,11:1217-1222.
[7] Lu Z, Negi S C, Jofriet J C. A numerical model for flow of granular materials in silos. Part 1: model development[J]. Journal of Agricultural Engineering Research,1997,68:223-229.
[8] Markauskas D, Kaianauskas R, Džiugys A, et al. Investigation of adequacy of multi-sphere approximation of elliptical particles for DEM simulations[J]. Granular Matter, 2010, 12: 107-123.
[9] 赵历. 组合椭球颗粒模型的三维离散单元法的研究[D]. 长春:吉林大学计算机科学与技术学院,2010.
Zhao Li. Research of three-dimensional discrete element method based on combination ellipsoid particle model[D]. Changchun:Collegc of Computer Science and Technology,Jilin University,2010.
[10] Zhou Y C, Wright B D, Yang R Y, et al. Rolling friction in the dynamic simulation of sandpile formation[J]. Physica A,1999,269:536-553.
[11] Coşkun M B, Yalçin Ì, Özarslan C. Physical properties of sweet corn seed ( Zea mays saccharata Sturt)[J]. Journal of Food Engineering,2006,74(4):523-528.
[12] ASAE. S368.4 DEC2000(R2006).Compression test of food materials of convex shape[S].
[13] Kibar H, Öztürk T. Physical and mechanical properties of soybean[J]. International Agrophysics,2008,22:239-244.
[14] González-Montellano C, Fuentes J M, Ayuga-Téllez E, et al. Determination of the mechanical properties of maize grains and olives required for use in DEM simulations[J]. Journal of Food Engineering,2012,111:553-562.
[15] 张列男. 基于离散元法的大豆精密排种器的数字化设计方法研究[D]. 长春:吉林大学生物与农业工程学院,2009.
Zhang Lie-nan. Digital design method of soybean precision seed-metering device based on DEM[D]. Changchun:College of Biological and Agricultural Engineering, Jilin University,2009.
[16] 崔涛,刘佳,杨丽,等. 基于高速摄像的玉米种子滚动摩擦特性试验与仿真[J]. 农业工程学报,2013,29(15):34-41.
Cui Tao, Liu Jia, Yang Li, et al. Experiment and simulation of rolling friction characteristic of corn seed based on high-speed photography[J]. Transactions of the Chinese Society of Agricultural Engineering,2013,29(15):34-41.
[17] Misra R N, Young J H. A model for predicting the effect of moisture content on the modulus of elasticity of soybeans[J]. Transactions of the ASAE,1981,24(5):1338-1341.
[18] LoCurto G J, Zhang X, Zakirov V, et al. Soybean impacts: experiments and dynamic simulations[J]. Transactions of the ASAE,1999,40(3):789-794.
[19] Wong C X, Daniel M C, Rongong J A. Energy dissipation prediction of particle dampers[J]. Journal of Sound and Vibration,2009,319:91-118.
[1] 王扬, 王晓梅, 陈泽仁, 于建群. 基于离散元法的玉米籽粒建模[J]. 吉林大学学报(工学版), 2018, 48(5): 1537-1547.
[2] 贾洪雷, 王万鹏, 陈志, 庄健, 王文君, 刘慧力. 基于土壤坚实度的仿形弹性镇压辊镇压力实时测量方法[J]. 吉林大学学报(工学版), 2018, 48(4): 1169-1175.
[3] 陈东辉, 吕建华, 龙刚, 张宇晨, 常志勇. 基于ADAMS的半悬挂式农业机组静侧翻稳定性[J]. 吉林大学学报(工学版), 2018, 48(4): 1176-1183.
[4] 李俊烨, 乔泽民, 杨兆军, 张心明. 介观尺度下磨料浓度对磨粒流加工质量的影响[J]. 吉林大学学报(工学版), 2017, 47(3): 837-843.
[5] 贾洪雷, 郑嘉鑫, 袁洪方, 郭明卓, 王文君, 于路路. 大豆播种机双V型筑沟器设计与试验[J]. 吉林大学学报(工学版), 2017, 47(1): 323-331.
[6] 肖志锋, 乐建波, 吴南星, 刘相东. 操作压力对过热蒸汽流化床干燥的影响[J]. 吉林大学学报(工学版), 2015, 45(4): 1375-1380.
[7] 张金波,佟金,马云海. 仿生肋条结构表面深松铲刃的磨料磨损特性[J]. 吉林大学学报(工学版), 2015, 45(1): 174-180.
[8] 齐龙, 谭祖庭, 马旭, 陈国锐, 谢俊锋, 邝健霞. 气动振动式匀种装置工作参数的优化及试验[J]. 吉林大学学报(工学版), 2014, 44(6): 1684-1691.
[9] 陈莉, 孙永海, 谢高鹏, 毛倩. 基于离散元法的咀嚼过程分析[J]. 吉林大学学报(工学版), 2014, 44(5): 1517-1524.
[10] 齐龙, 廖文强, 马旭, 林建衡, 区志行, 詹志勋. 水田小型除草机器人平台控制系统设计与测试[J]. 吉林大学学报(工学版), 2013, 43(04): 991-996.
[11] 翟治芬, 严昌荣, 张建华, 张燕卿, 刘爽. 基于蚁群算法和支持向量机的节水灌溉技术优选[J]. 吉林大学学报(工学版), 2013, 43(04): 997-1003.
[12] 姚亮, 初亮, 周飞鲲, 刘明辉, 张永生, 魏文若. 纯电动轿车制动能量回收节能潜力仿真分析[J]. 吉林大学学报(工学版), 2013, 43(01): 6-11.
[13] 王登峰, 季枫, 陈书明, 苏丽俐, 郝赫. 多轴重型汽车气动制动防抱死系统性能仿真与试验[J]. 吉林大学学报(工学版), 2012, 42(增刊1): 7-12.
[14] 张强, 于路路, 贾洪雷. 拖拉机用装卸装置的设计与试验[J]. 吉林大学学报(工学版), 2012, 42(增刊1): 108-112.
[15] 周德义, 王子佳, 张丹丹, 吴冠军, 周晗宇. 新型玉米收获机的秸秆处理装置[J]. 吉林大学学报(工学版), 2012, 42(增刊1): 113-116.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 王文权, 商延赓, 李秀娟, 王春生, 张桂兰. 激光焊接650 MPa相变诱发塑性钢的组织与性能[J]. , 2012, 42(05): 1203 -1207 .
[2] 黄健康1, 何翠翠1, 2, 石玗1, 樊丁1. 铝/钢异种金属焊接接头界面Al-Fe金属间化合物生成及其热力学分析[J]. 吉林大学学报(工学版), 2014, 44(4): 1037 -1041 .
[3] 徐涛, 刘光洁, 葛海潮, 张炜, 于征磊. 焊接热源局部坐标移动曲线路径建模方法[J]. 吉林大学学报(工学版), 2014, 44(6): 1704 -1709 .
[4] 骆海涛, 周维佳, 王洪光, 武加锋. 搅拌摩擦焊机器人典型工况下的受载分析[J]. 吉林大学学报(工学版), 2015, 45(3): 884 -891 .
[5] 杨悦, 周磊磊. 微弧氧化对铝合金搅拌摩擦焊缝耐蚀性能的影响[J]. 吉林大学学报(工学版), 2016, 46(2): 511 -515 .
[6] 初亮, 孙成伟, 郭建华, 赵迪, 李文惠. 基于轮缸压力的制动能量回收评价方法[J]. 吉林大学学报(工学版), 2018, 48(2): 349 -354 .
[7] 何祥坤, 季学武, 杨恺明, 武健, 刘亚辉. 基于集成式线控液压制动系统的轮胎滑移率控制[J]. 吉林大学学报(工学版), 2018, 48(2): 364 -372 .
[8] 张天时, 宋东鉴, 高青, 王国华, 闫振敏, 宋薇. 电动汽车动力电池液体冷却系统构建及其工作过程仿真[J]. 吉林大学学报(工学版), 2018, 48(2): 387 -397 .
[9] 袁朝春, 张龙飞, 陈龙, 何友国, 范兴根. 基于路面辨识的主动避撞系统制动性能[J]. 吉林大学学报(工学版), 2018, 48(2): 407 -414 .
[10] 徐洪峰, 高霜霜, 郑启明, 章琨. 信号控制交叉口的复合动态车道管理方法[J]. 吉林大学学报(工学版), 2018, 48(2): 430 -439 .