吉林大学学报(工学版) ›› 2016, Vol. 46 ›› Issue (3): 725-731.doi: 10.13229/j.cnki.jdxbgxb201603007

• 论文 • 上一篇    下一篇

汽车空调压缩机怠速噪声诊断及拓扑优化

史文库1, 祖庆华1, 陈志勇1, 毛阳1, 何邦颖1, 付吉云1, 黎晓燕2   

  1. 1.吉林大学 汽车仿真与控制国家重点实验室,长春 130022;
    2.牡丹江富通汽车空调有限公司 产品工程部,黑龙江 牡丹江 157000
  • 收稿日期:2015-01-09 出版日期:2016-06-20 发布日期:2016-06-20
  • 通讯作者: 陈志勇(1980-),男,讲师,博士.研究方向:整车NVH控制.E-mail:chen_zy@jlu.edu.cn
  • 作者简介:史文库(1960),男,教授,博士生导师.研究方向:整车NVH控制.E-mail:phdofjlu@126.com
  • 基金资助:
    国家自然科学基金项目(51205158); 中国博士后科学基金项目(2013M541294).

Noise diagnosis of in idle automotive air conditioning compressor and topology optimization

SHI Wen-ku1, ZU Qing-hua1, CHEN Zhi-yong1, MAO Yang1, HE Bang-ying1, FU Ji-yun1, LI Xiao-yan2   

  1. 1.State Key Laboratory of Automotive Simulation and Control, Jilin University, Changchun 130022, China;
    2.Department of Product Engineering, Mudanjiang Futong Automotive Air Conditioning Co., Ltd.,Mudanjiang 157000, China
  • Received:2015-01-09 Online:2016-06-20 Published:2016-06-20

RICH HTML

0   

PDF (PC)

151

摘要： 针对某国产SUV车型怠速开空调时车内噪声较大的问题,对样车及其压缩机系统进行了试验诊断、分析和改进。通过分析试验获得的车内噪声频谱和压缩机振动频谱,结合压缩机及支架系统的模态计算和试验验证,认定开、关空调噪声差异主要是由压缩机工作频率与压缩机及其支架系统一阶固有频率接近产生共振造成的。通过拓扑优化的方法对支架结构进行了加强,提高了压缩机-支架系统的一阶模态频率,避开了怠速开空调时压缩机的工作频率。将改进的支架装车进行试验验证,结果表明:在怠速开空调工况下,改进后的车内噪声比改进前降低了2.3 dB(A),改进效果明显;定置升转速工况试验结果表明:改进后在发动机转速为900~3400 r/min时,车内噪声有明显降低。

关键词: 车辆工程, 汽车空调压缩机, 噪声诊断, 拓扑优化

Abstract: Test diagnosis, analysis and improvement of a SUV and its air conditioning system are carried out to solve the inner noise problem, which is generated while the air conditioning is turned in idle. The test frequency spectrum analysis of inner noise and compressor vibration, modal analysis and test validation show that the working frequency of the compressor is close to the system's first order frequency. This causes resonance, which leads to obvious noise difference between turning on and turning off the air conditioning in idle. To solve this problem, the shape of the compressor support is improved by topology optimization. Modal analysis indicates that the first order modal frequency of the improved support keeps away from the working frequency of the compressor. The improved support is test and the results indicate that the inner noise is reduced by 2.3 dB(A), and the noise decreases obviously when the engine speed is from 900 r/min to 3000 r/min in run up condition.

Key words: vehicle engineering, automotive air conditioning compressor, noise diagnosis, topology optimization

中图分类号: 

  • U463.8
[1] 林逸,马天飞,姚为民,等. 汽车NVH特性研究综述[J]. 汽车工程,2002,24(3):177-186.
Lin Yi,Ma Tian-fei,Yao Wei-min, et al. The sunnary of study on vehicle NVH performance[J]. Automotive Engineering,2002,24(3):177-186.
[2] 李沛然,邓兆祥,叶常景.汽车NVH试验数据管理系统关键技术研究[J].振动与冲击,2010,29(2):163-166.
Li Pei-ran, Deng Zhao-xiang, Ye Chang-jing. Key techniques of a test data management system for automotive NVH[J]. Journal of Vibration and Shock,2010,29(2):163-166.
[3] Humbad N. Automotive HVAC noise measurements and analysis[J]. Chinese Journal of Automotive Engineering,2011,1(4):299-309.
[4] 潘军,王屹,蒋祖华,等. 斜盘式汽车空调压缩机动力特性仿真[J]. 流体机械,2002,30(1):44-48.
Pan Jun,Wang Yi,Jiang Zu-hua,et al.Dynamic simulation of swach plate compressor in automotive air conditioning system[J].Fluid Machinery,2002,30(1):44-48.
[5] Lietz C. Automotive HVAC hiss noise measurements[J]. Chinese Journal of Automotive Engineering,2011,1(4): 263-271.
[6] 孙启甲. 实车空调系统异响诊断技术研究[D]. 重庆:重庆大学机械工程学院,2012.
Sun Qi-jia. Study on abnormal sound diagnosis of car's conditioning system[D]. Chongqing:College of Mechanical Engineering, Chongqing University,2012.
[7] 卢喜,杨诚. 旋叶式汽车空调压缩机的噪声源识别[J]. 重庆大学学报:自然科学版,2006,29(8):70-73.
Lu Xi, Yang Cheng. Identifying research on noise sources of rotary vane compressor[J]. Journal of Chongqing University(Nature Science Edition),2006,29(8):70-73.
[8] 房师毅,李连生,束鹏程,等. 无油润滑涡旋式空调压缩机的工作过程研究[J]. 中国机械工程,2005,16(2):123-127.
Fang Shi-yi,Li Lian-sheng, Shu Peng-cheng,et al. Study on working process of an oil-free scroll air compressor[J]. China Mechanical Engineering,2005,16(2):123-127.
[9] 张立军,靳晓雄,黄锁成,等.汽车空调压缩机引起的车内噪声试验研究[J].汽车工程,2002,24(5):398-402.
Zhang Li-jun,Jin Xiao-xiong,Huang Suo-cheng,et al. Experimental reaserch on the car interior noise caused by air conditioning compressor[J]. Automotive Engineering, 2002,24(5):398-402.
[10] 黄锁成,靳晓雄,张立军,等. 汽车空调用压缩机的振动和噪声分析[J]. 汽车技术,2003(5):20-23.
Huang Suo-cheng,Jin Xiao-xiong,Zhang Li-jun, et al. Analysis of vibration and noises of automotive air-conditioner compressor[J]. Automobile Technology, 2003(5):20-23.
[11] 朱爱武. 空调压缩机对车内噪声的影响[J]. 噪声与振动控制,2010(4):47-49.
Zhu Ai-wu. Influence of air conditioner's compressor on vehicle interior noise[J]. Noise and Vibration Control, 2010(4):47-49.
[12] 江辉有. 拓扑学[M]. 北京:机械工业出版社,2013.
[13] 朱剑峰,林逸,陈潇凯,等. 汽车变速箱壳体结构拓扑优化设计[J]. 吉林大学学报:工学版,2013,43(3):584-589.
Zhu Jian-feng, Lin Yi, Chen Xiao-kai, et al. Structural topology optimization based design of automotive transmission housing structure[J]. Journal of Jilin University (Engineering and Technology Edition),2013,43(3):584-589.
[14] 赵红伟,陈潇凯,林逸. 电动汽车动力电池仓拓扑优化[J].吉林大学学报:工学版,2009,39(4):846-850.
Zhao Hong-wei,Chen Xiao-kai,Lin Yi. Topology optimization of power battery cabin in electric vehicle[J].Journal of Jilin University(Engineering and Technology Edition),2009,39(4):846-850.
[15] 上官文斌,蒋翠翠,潘孝勇.汽车悬架控制臂的拓扑优化与性能计算[J].汽车工程,2008,30(8):709-712.
Shangguan Wen-bin,Jiang Cui-cui,Pan Xiao-yong. Topology optimization and performance calculation for control arm of vehicle suspension[J]. Automotive Engineering,2008,30(8):709-712.
[1] 常成,宋传学,张雅歌,邵玉龙,周放. 双馈电机驱动电动汽车变频器容量最小化[J]. 吉林大学学报(工学版), 2018, 48(6): 1629-1635.
[2] 席利贺,张欣,孙传扬,王泽兴,姜涛. 增程式电动汽车自适应能量管理策略[J]. 吉林大学学报(工学版), 2018, 48(6): 1636-1644.
[3] 何仁,杨柳,胡东海. 冷藏运输车太阳能辅助供电制冷系统设计及分析[J]. 吉林大学学报(工学版), 2018, 48(6): 1645-1652.
[4] 那景新,慕文龙,范以撒,谭伟,杨佳宙. 车身钢-铝粘接接头湿热老化性能[J]. 吉林大学学报(工学版), 2018, 48(6): 1653-1660.
[5] 刘玉梅,刘丽,曹晓宁,熊明烨,庄娇娇. 转向架动态模拟试验台避撞模型的构建[J]. 吉林大学学报(工学版), 2018, 48(6): 1661-1668.
[6] 赵伟强, 高恪, 王文彬. 基于电液耦合转向系统的商用车防失稳控制[J]. 吉林大学学报(工学版), 2018, 48(5): 1305-1312.
[7] 宋大凤, 吴西涛, 曾小华, 杨南南, 李文远. 基于理论油耗模型的轻混重卡全生命周期成本分析[J]. 吉林大学学报(工学版), 2018, 48(5): 1313-1323.
[8] 朱剑峰, 张君媛, 陈潇凯, 洪光辉, 宋正超, 曹杰. 基于座椅拉拽安全性能的车身结构改进设计[J]. 吉林大学学报(工学版), 2018, 48(5): 1324-1330.
[9] 那景新, 浦磊鑫, 范以撒, 沈传亮. 湿热环境对Sikaflex-265铝合金粘接接头失效强度的影响[J]. 吉林大学学报(工学版), 2018, 48(5): 1331-1338.
[10] 王炎, 高青, 王国华, 张天时, 苑盟. 混流集成式电池组热管理温均特性增效仿真[J]. 吉林大学学报(工学版), 2018, 48(5): 1339-1348.
[11] 金立生, 谢宪毅, 高琳琳, 郭柏苍. 基于二次规划的分布式电动汽车稳定性控制[J]. 吉林大学学报(工学版), 2018, 48(5): 1349-1359.
[12] 隗海林, 包翠竹, 李洪雪, 李明达. 基于最小二乘支持向量机的怠速时间预测[J]. 吉林大学学报(工学版), 2018, 48(5): 1360-1365.
[13] 王德军, 魏薇郦, 鲍亚新. 考虑侧风干扰的电子稳定控制系统执行器故障诊断[J]. 吉林大学学报(工学版), 2018, 48(5): 1548-1555.
[14] 胡满江, 罗禹贡, 陈龙, 李克强. 基于纵向频响特性的整车质量估计[J]. 吉林大学学报(工学版), 2018, 48(4): 977-983.
[15] 刘国政, 史文库, 陈志勇. 考虑安装误差的准双曲面齿轮传动误差有限元分析[J]. 吉林大学学报(工学版), 2018, 48(4): 984-989.
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed   
No Suggested Reading articles found!
版权所有 © 《吉林大学学报(工学版)》编辑部
地址：长春市人民大街5988号　电话：+86-431-85095297　传真：+86-431-85094074　E-mail: xbgxb@jlu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发